beautypg.com

Operating instructions – Euro-Pro EP709 User Manual

Page 6

background image

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

Warning:

To reduce the risk of electric

shock, the power cord must be

disconnected before changing the dust bag or
performing maintenance/trouble shooting checks.

Replacing the Dust Bag

1. To open main unit, press the storage

compartment release button to unlock and lift

the cover. (Fig. 4)

Note Vacuuming new carpet or carpet

with fine powders may clog the dust

bag, so check the bag more often.

Never operate without dust bag in

place.

2. Remove the old dust bag by pushing the

paper bag holder towards the rear of the

unit and then pull up on the cardboard

collar. Dispose of paper bags. Never

reuse Paper Bags.

3. To insert a new dust bag slide the

cardboard collar end with the slot into the

matching slot on the holder (a). Cardboard

should be behind the (2) two securing tabs

on holder. Press the paper bag holder (b)

toward the front of the unit and make sure

that the paper bag is locked in place.

(Fig. 5)

4. Close storage compartment cover.

Warning:

Before closing main unit,

make certain that paper bag is well inside

the compartment and does not get caught
between the hinges when closing the cover.

Fig. 4

Fig. 5

Paper bag

holder

b) Push in

a) Cardboard

insert

The vacuum cleaner has a built-in pressure

safety valve. As soon as the dust bag is full

or the suction hose is blocked, the dust bag

full light will come on. If the suction power is

noticeably diminished, first check if the

suction hose is blocked. Then check if dust

bag is full. If this is the case, change it. We

recommend that the dust bag be changed

when it is 2/3 full so that full suction can

be maintained.

Changing the Pre-Motor Filter

The pre-motor filter is located inside the

storage compartment behind the dust bag.

(Fig. 6)

The pre-motor filter should be cleaned at

least twice a year or when it becomes

visibly soiled.

Always operate the cleaner with the filter

installed.

Disconnect from electrical outlet

before cleaning the filter.

Do not use a washing machine to

rinse the filter.

Do not use a hair dryer to dry it.

Always allow 24 hours to air dry.

1. Press the storage compartment release

button and open the cover.

2. Remove the paper bag from the unit.

3. Pull the pre-motor filter assembly out of

the unit.

4. Remove the pre-motor filter from the

filter grill.

5. Rinse the pre-motor filter in lukewarm

water and let the pre-motor filter air dry

for 24 hours until it is completely dry.

(Fig. 7)

6. Replace the pre-motor filter into the filter

grill and replace back into the unit.

7. Replace the dust bag and close the

storage compartment cover.

Pre-motor

filter

Fig. 6

Full Dust Bag Indicator

Your vacuum cleaner includes a manual

variable suction control. The suction power can

be adjusted by moving the slide regulator to the

desired position between Open and Closed.

(Fig. 3) Open gives you less suction, closed
maximum suction. For example, less suction is

required on upholstery and draperies compared

to thick carpets, which require maximum

suction.

Fig. 3

1.

Crevice Tool with Brush
For radiators, crevices,

corners, baseboards and

between cushions.

2.

Upholstery Brush
The upholstery brush is

used for the furniture

Note:

Once all

attachments are

in place, unwind

a sufficient length

of cable and insert

the plug into the

wall outlet. A

yellow mark on

The power cord

shows the ideal

cable length. Don't pull the power cord

beyond the red mark.

1. Insert the power plug into the wall

outlet. (Fig. 1)

2. Press the Power

On/Off button

located on the

unit to turn the

vacuum cleaner

"On".

3. To rewind the

power cord, press the cord rewind

button with one hand and hold the

plug of the power cord with the other

hand to ensure that it does not whip

causing damage or injury. (Fig. 2)

Using your Vacuum

Fig. 2

Fig. 1

On/Off

Switch

Crevice Tool and Dusting Brush

Assembling Your Vacuum Cleaner
Note:

Always remove the power plug

from the wall outlet before assembling or

removing accessories.

2. Fitting the Extension Tubes

to the Flexible Hose

Push the extension tube that is
without the parking position hook

into the curved wand / hose

extension, as shown in the

illustration below. Then insert the

other extension tube into this one.

1. Attaching the Flexible Hose

to the Vacuum

Connect the flexible hose into the

hose inlet. Push in until you hear a

“click”, indicating it is in its locked

position.

3. Fitting the Floor to Carpet

Brush to the Extension Tube

Push the end of the extension tube
into the floor-to-carpet brush as

show in the illustration below.

Floor to Carpet
Brush

Extension

Tube

Manual Suction Control

Fig. 7

5

4