Euro-Pro XDB520H - Manual (Page 2)

Replacing the Filters
2 Sets Pre-Motor Filters
2 Sets Post Motor Filters
Replacing the Filters
2 Sets Pre-Motor Filters
2 Sets Post Motor Filters
Warning: To reduce the risk of electric shock, the power cord must be disconnected
before changing the bag or performing maintenance/ troubleshooting.
Warning: To reduce the risk of electric shock, the power cord must be disconnected
before changing the bag or performing maintenance/ troubleshooting.
Changing & Cleaning the
Pre-Motor Filter
Your vacuum is equipped with a filtration
system to reduce dust and pollen in your
home as you clean. The pre-motor filter
is located inside the vacuum cleaner
body behind the dust bag. Check when
changing the dust bag and replace when
dirty.
This is a rinse-able filter but should be
replaced every three (3) to six (6)
months, depending on usage. Never
operate the vacuum without ALL the
filters in place
1. Push the Power On/Off button to the
"Off" position and disconnect the
power cord from the wall outlet.
2. To remove, open the dust bag
compartment cover and remove the
pre-motor filter out of the vacuum.
3. Rinse in lukewarm water and let it air
dry completely for 24 hours. Do not
use a washing machine to rinse the
filter. Do not use a hair dryer to dry it.
Air dry only. When the pre-motor
filter is completely dry, insert the filter
into the vacuum. (Fig. 1)
Changing & Cleaning the
Pre-Motor Filter
Your vacuum is equipped with a filtration
system to reduce dust and pollen in your
home as you clean. The pre-motor filter
is located inside the vacuum cleaner
body behind the dust bag. Check when
changing the dust bag and replace when
dirty.
This is a rinse-able filter but should be
replaced every three (3) to six (6)
months, depending on usage. Never
operate the vacuum without ALL the
filters in place
1. Push the Power On/Off button to the
"Off" position and disconnect the
power cord from the wall outlet.
2. To remove, open the dust bag
compartment cover and remove the
pre-motor filter out of the vacuum.
3. Rinse in lukewarm water and let it air
dry completely for 24 hours. Do not
use a washing machine to rinse the
filter. Do not use a hair dryer to dry it.
Air dry only. When the pre-motor
filter is completely dry, insert the filter
into the vacuum. (Fig. 1)
Fig. 2 Fig. 3
Changing & Cleaning the Post
Motor Filter
The post motor filter should be replaced
every three (3) to six (6) months
depending on usage. Never operate the
vacuum without ALL the filters in place.
1. Push the Power On/Off button to the
"Off" position and disconnect the
power cord from the wall outlet.
2. The post motor filter is located at the
rear of the unit.
3. Push down on the tab of the post
motor filter assembly and pull the
assembly out. (Fig. 2)
4. Remove the post-motor from the
filter assembly. (Fig. 3)
5. Rinse in lukewarm water and let it air
dry completely for 24 hours. Do not
use a washing machine to rinse the
filter. Do not use a hair dryer to dry it.
Air dry only. When the post-motor
filter is completely dry, insert it in the
filter into the vacuum.
Fig. 2 Fig. 3
Changing & Cleaning the Post
Motor Filter
The post motor filter should be replaced
every three (3) to six (6) months
depending on usage. Never operate the
vacuum without ALL the filters in place.
1. Push the Power On/Off button to the
"Off" position and disconnect the
power cord from the wall outlet.
2. The post motor filter is located at the
rear of the unit.
3. Push down on the tab of the post
motor filter assembly and pull the
assembly out. (Fig. 2)
4. Remove the post-motor from the
filter assembly. (Fig. 3)
5. Rinse in lukewarm water and let it air
dry completely for 24 hours. Do not
use a washing machine to rinse the
filter. Do not use a hair dryer to dry it.
Air dry only. When the post-motor
filter is completely dry, insert it in the
filter into the vacuum.
Fig. 1 Fig. 1