EarthQuake PH-2000W-D1.1 - Manual (Page 3)

4
Specifications Are Subject To Change Without Notice
5
Please keep this warranty information in your
files for future reference if necessary. It is
recommended that you stick your serial number
here for future reference.
SERIAL NUMBER
SPECIFICA
TIONS
Model
Channels
PH800W/2 PH1000W/2 PH2200W/4 PH2000W/D1 PH5000W/D1 PH10000W/D1 PH2000W/D1.1
2 2 4
1 (MONO) 1
(MONO)
1
(MONO)
1
(MONO)
Max Power
800 1000 1400 1400 1400 5000 5000
Power 4-Ohm Bridged
Power 2-Ohm Bridged
Power 4-Ohm Stereo
1 x 400 1 x 500 2 x 500
2 x 200 2 x 250 4 x 250 1 x 1000 1 x 700 1 x 3000 1 x 3000
2 x 105 2 x 145 4 x 130 1 x 500 1 x 450 1 x 860
PH20000WD
2
20000
1 x 20,000
2 x 3000 1 x 900
Power 1-Ohm
N/A N/A N/A N/A
1 x 1000 1 x 5000 1 x 5000
N/A
MONO MONO MONO MONO
6000
Dimensions (HxWxL)
2.375" x 10.125" x 8.5"
2.375" x 10.125" x
10.375"
2.375" x 10.125" x 13.375"
2.375" x 10.125" x 12" 2.375" x 10.125" x 12" 2.375" x 10.125" x 15"
2.375" x 10.125" x 16.5"
4.5" x 12" x 28.625"
W
eight 13.5
9 1
1
13 13 16 18
www.earthquakesound.com
A warranty claim will not be valid if the warranty registration card is not properly filled and
returned to Earthquake with a copy of the purchase receipt.
(E) Service Request:
To receive product(s) service, contact Earthquake service department at (510) 732-1000
and request an RMA (Return Material Authorization) number. Items shipped without a
valid RMA number will be refused. Make sure you provide us with your complete/correct
shipping address (NO P.O. Box), a valid phone number and a brief description of the
problem you are experiencing with the product(s). In most cases, our technicians might be
able to resolve the problem over the phone, thus eliminating the need to ship the
product(s).
(F) Shipping Instructions:
Product(s) must be packaged in its original protective box(es) to minimize transport
damage, otherwise a re-packing charge may apply. Shipper claims regarding items
damaged in transit must be presented to carrier. Earthquake Sound Corporation reserves
the right to refuse products that are improperly packed. Copy of original purchase receipt
must accompany product(s) being returned for service. We encourage you to include with
the package a written description of the problem.
Ship product to:
Earthquake Sound Corp.
2727 Mc Cone Avenue. Hayward, CA 94545
Phone: (510) 732-1000
You are responsible for the cost of shipping and insurance for the product(s). Please be
sure to write the RMA number on every box.
(G) Disputes Resolution:
All disputes - between client(s) and Earthquake Sound Corporation - resulting from the
five (5) year limited warranty policy must be resolved according to the laws & regulations
of the county of Alameda, California.
WARRANTY
***
ALL
MEASUREMENTS
ARE MADE USING RESISTIVE LOAD ***
***
ALL
POWER RA
TINGS
ARE PEAK POWER ***
SIGNAL
SENSOR
This new feature allows you to eliminate the use of a remote wire to turn on your amplifier
.
!
When
in
“AUT
O
ON”
mode,
the
amplifier
will
automatically
detect
an
incoming
signal
once
the
stereo
is
turned
on.
If
the
amplifier
does
not
detect
a
signal
within
20
minutes,
it
will
automatically
shuts
down.
!
When
in
“REMOTE
ON”
mode,
the
amplifier
relies
on
the
remote
wire
to
detect
a
signal.
NOTE:
The
RCA
outputs
must
be
inserted
in
CH1/2
for
the
amplifier
to
detect
any
incoming
signal.
NOTE:
In
some
cases
when
the
amplifier
is
on
“AUT
O
ON”
mode,
if
your
system
generates
noise
through
the
RCA
wire
and
therefore
waking
up
the
amplifier
,
you
may
want
to
switch
your
amplifier
installation
to
the
“REMOTE
ON”
mode
(must
use
the
turn
on
wire). NOTE: For warranty guidelines on the PH5000W/D1, PH10000W/D1 and
PH20000W/D, please refer to the one provided in the product packaging.