Euro-Pro BIG SHARK V1505 - Manual (Page 3)

OPERATING INSTRUCTIONS cont. GETTING TO KNOW YOUR BIG SHARK
The post motor filter is a washable filter
but should be replaced every three (3)
months depending on usage.
• Disconnect from electrical outlet
before cleaning or changing the filter.
• Remove the exhaust cover from the
rear of the unit.
• Rinse the post motor filter in
lukewarm water and dry the filter
completely. Do not use a washing
machine to rinse the filter. Do not
use a hair dryer to dry it. Air dry only
for 24 hours. Never operate the
vacuum without the post motor filter
in place.
• A severely clogged filter should be
thoroughly washed with fresh tepid
water. A mild detergent can be used
if required.
IMPORTANT: This unit is equipped
with a motor protective thermostat. If
for some reason the vacuum cleaner
should overheat, the thermostat will
automatically turn the unit off. Should
this occur:
• Push the On/Off button once.
• Disconnect the plug from the
power source.
• Check the source of overheating
problem. (i.e. clogged hose or
filter)
• If clogged hose or filter is found,
unclog the hose and replace the
filters.
• Wait at least 45 minutes before
attempting to reuse the vacuum.
• After unit has cooled down for
45 minutes, plug in the cleaner
and push the On/Off button. The
vacuum should start again.
• If the vacuum still does not start,
contact EURO-PRO at
1-800-798-7398.
Motor Thermostat
HEPA Filter Debris Screen
8. Dust Cup (Container)
9. Flexible Hose
10. Oval Brush
11. Crevice Tool
12. Shoulder Strap
13. HEPA Dust Cup Filter
w/Debris Screen
1. Dust Cup Release Button
2. On/Off Power Switch
3. Intelli-Sense TM Filter Monitor
4. Handle
5. Shoulder Strap Attachment Points
6. Suction Hole
7. Exhaust Cover
TROUBLE SHOOTING GUIDE
PROBLEM POSSIBLE REASON POSSIBLE SOLUTION
HAND VACUUM
WILL NOT
OPERATE
1. Power cord not firmly plugged
into outlet.
2. No power in wall outlet.
3. Needs servicing.
4. Thermostat has tripped.
1. Plug unit in firmly.
2. Check fuse or breaker.
Replace fuse/reset breaker.
3. Call 1-800-798-7398.
4. Turn the unit off and unplug
from outlet. Allow unit to cool
down; then restart.
HAND VACUUM
WILL NOT PICK-UP
OR SUCTION
POWER IS WEAK
1. Dust cup is full.
2. Unit clogged.
3. HEPA Dust Cup Filter needs
cleaning or replacing.
1. Empty and clean dust cup –
(see page 4).
2. Turn unit off and unplug
from wall outlet. Remove
HEPA Dust Cup Filter and
check for object(s) in air
duct and remove.
3. Clean or replace HEPA
Dust Cup Filter.
(see page 4)
DUST ESCAPING
FROM HAND
VACUUM
1. Dust cup is full.
2. HEPA Dust Cup Filter is not
installed correctly.
3. There is a puncture/hole in
HEPA Dust Cup Filter.
1. Empty and clean dust cup.
(see page 4)
2. Review HEPA Dust Cup
Filter instructions.
(see page 4)
3. Replace HEPA dust cup
filter. (see page 4)
HAND VACUUM
HOSE OR
BRUSHES WILL
NOT PICK-UP
1. Hose clogged.
2. Dust cup is full.
1. Remove hose and/or
bushes. Remove obstruction
from hose.
2. Empty and clean dust cup.
5
Technical Specifications
Voltage: 120V., 60Hz.
Power: 7.5 Amps, 900 Watts
2