Adam Hall 19" Rack Drawer with Built-In Combination Lock (2 RU, Steel) - Manual

Adam Hall GmbH | Adam-Hall-Str. 1 | 61267 Neu-Anspach | Germany
Phone: +49 6081 9419-0 | adamhall .com
8740x CL
RACK DRAWER 2HE / 3HE / 4HE / 6HE STEEL
WITH BUILT-IN COMBINATION LOCK
SAFETY INFORMATION
1. Please read these instructions carefully.
2. Keep all information and instructions in a safe place.
3. Follow the instructions.
4. Observe all safety warnings. Never remove safety warnings or other information from the
equipment.
5. Use the equipment only in the intended manner and for the intended purpose.
6. Use only sufficiently stable and compatible stands and/or mounts (for fixed installations).
Make certain that wall mounts are properly installed and secured. Make certain that the
equipment is installed securely and cannot fall down.
7. During installation, observe the applicable safety regulations for your country.
8. Never install and operate the equipment near radiators, heat registers, ovens or other sourc-
es of heat. Make certain that the equipment is always installed so that is cooled sufficiently
and cannot overheat.
9. Never place sources of ignition, e.g., burning candles, on the equipment.
10. Ventilation slits must not be blocked.
11. Do not use this equipment in the immediate vicinity of water (does not apply to special out-
door equipment - in this case, observe the special instructions noted below. Do not expose
this equipment to flammable materials, fluids or gases.
12. Make certain that dripping or splashed water cannot enter the equipment. Do not place con-
tainers filled with liquids, such as vases or drinking vessels, on the equipment.
13. Make certain that objects cannot fall into the device.
14. Use this equipment only with the accessories recommended and intended by the manufac-
turer.
15. Do not open or modify this equipment.
16. After connecting the equipment, check all cables in order to prevent damage or accidents, e.g.,
due to tripping hazards.
17. During transport, make certain that the equipment cannot fall down and possibly cause prop-
erty damage and personal injuries.
18. If your equipment is no longer functioning properly, if fluids or objects have gotten inside the
equipment or if it has been damaged in another way, switch it off immediately and unplug
it from the mains outlet (if it is a powered device). This equipment may only be repaired by
authorized, qualified personnel.
19. Clean the equipment using a dry cloth.
20. Comply with all applicable disposal laws in your country. During disposal of packaging, please
separate plastic and paper/cardboard.
21. Plastic bags must be kept out of reach of children.
MANUFACTURER’S WARRANTY & LIMITATION OF LIABILITY
You can find our current warranty conditions and limitation of liability at: https://cdn-shop.adam-
hall.com/media/pdf/MANUFACTURERS-DECLARATIONS_ADAM_HALL.pdf
To request warranty service for a product, please contact Adam Hall GmbH, Adam-Hall-Str. 1,
61267 Neu Anspach / Email [email protected] / 49 (0) 6081 / 9419-0
PROPER DISPOSAL OF THIS PRODUCT
(WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT)
(Valid in the European Union and other European countries with waste separation)
This symbol on the product, or the documents accompanying the product, indicates that this ap-
pliance may not be treated as household waste. This is to avoid environmental damage or person-
al injury due to uncontrolled waste disposal. Please dispose of this product separately from other
waste and have it recycled to promote sustainable economic activity.
Product number 87402CL 87403CL 87404CL 87406CL
Product type 19" Rack Drawers
Type 2 U 3 U 4 U 6 U
Material Steel
Surface Powder coated
Material combination lock Zinc alloy
Color Black
Outside height 2 U 3 U 4 U 6 U
Outside width (mm) 434 434 434 434
Outside depth (mm) 392 392 392 392
Inside height (mm) 74 120 175 255
Inside width (mm) 401 401 401 401
Internal depth (mm) 373 373 373 373
Max. load capacity 25 kg
Material thickness (mm) 2 mm
Weight (kg) 7 8.2 9.4 13.802
FEATURES
• Full extension
• Drawer on ball-bearing slide-in rail
• Combination lock
• Removable by quick disconnection of the slide-in rails
HOW TO RESET YOUR NUMBER COMBINATION?
1. Locate the reset button in the small opening at the back of the lock.
2. With a pen or sharp object, keep the reset button pressed while setting your new
combination.
3. Release the reset button to validate the new code.
SPECIFICATIONS