Operating instructions – Euro-Pro EP922HA User Manual

Page 8

OPERATING INSTRUCTIONS

Components

Power “On” Light (red): This light will

illuminate when the unit is plugged into

the 120V. wall outlet. This light will cycle

on and off with the steam ready light.

CAUTION:

Read the instructions

for “Filling the Water Tank” before

opening the Safety Cap.

CAUTION:

Always unplug

before filling. ALLOW UNIT TO

COOL FOR FIFTEEN (15)

MINUTES BEFORE REFILLING.

IMPORTANT:

Do NOT add cleaning

solutions, scented perfumes, oils or any

other chemicals to the water used in this

appliance. Use tap water or

distilled/purified water if the tap water

in your area is very hard.

Filling or Refilling Your Steam

Cleaner With Water
IMPORTANT:

Always insure that the unit

is “UNPLUGGED” from the wall receptacle

prior to initial filling or re-filling the water

tank and has been allowed to cool for 15

minutes. Never attempt to fill this unit

under a water tap, always use the filling

funnel provided.

Step 6: Connect desired attachments

onto the Flexible Steam Hose.

Step 7: Plug the unit into a standard (120

volt, grounded) wall receptacle.

Allow approximately 8-10 minutes

for vapor to reach its working

temperature and pressure. The

green ready light will illuminate

when the unit is ready for use.

Always point nozzle outlet in a safe

direction.

NOTE:

When the steam cleaner has run

out of water, steam output will cease.

Remove the funnel slowly and let

the remaining water in it to go

inside the water tank. Do Not

Overfill. Replace the Safety

Filler Cap.

WARNING:

Allow unit to cool for

15 minutes before refilling. When

refilling the steam cleaner while the

boiler is still hot, there is a risk that

water will squirt back during filling

and cause scalding. Extreme care

should be taken when refilling the

unit. Use caution when opening the

Safety/Filler Cap as cap may become

hot during use and escaping steam

can cause scalding.

Fig. 5

Attaching the Steam Pocket
Towel to the Frame
WARNING:

Always insure the unit is

“UNPLUGGED” from the wall

receptacle prior to attaching or

removing accessories.

Fig. 10

Note that the flat on the nozzle

must face toward the side of the

frame with the brass pin. Once

inserted, rotate it 90°.

Step 3: Insert the electrical power cord

into the outlet. Heating time

is approximately 8-10 minutes

with cold water. Filling the steam

generator with hot water will

shorten the heat up time.

Fig. 8

Fig. 7

Step 1: Connect one of the extension

tubes to the hand grip on the

flexible steam hose. To

attach the extension tubes

one onto the other or onto the

hand grip, press the locking

button ensuring that it fits into the

hole. (Fig. 7, Fig. 8) To

disconnect, repeat the operation

by pressing the locking button

and pulling the two sections

apart.

NOTE:

Fit the steam pocket frame with

the angle adapter onto the extension tube.

Step 2: If the angle adapter is not

attached to the steam pocket

frame, attach as follows: Hold

the steam pocket frame in one

hand and the

angle adapter in the

other. Insert the

angle adapter

stem into the

opening of the

steam pocket frame as

shown in Fig. 9

Fig. 9

Using the Variable Steam
Feature

Your steam cleaner has a variable

steam feature that allows you to adjust

the steam flow to the job that you are

doing. For example, set the variable

steam at lower settings when using

the window squeegee and at higher

settings when cleaning grout seams.

The variable steam control is located

on the handgrip. Fig. 6 To increase the

steam flow, turn the knob counter

clockwise and to decrease, turn it

clockwise.

Fig. 6

Using Your Steam Cleaner with
Steam Pocket

1. Slide the steam

pocket towel over

the steam pocket

frame. (Fig. 10)

Fig.11

3. Bring the velcro strips

that are on the

back side of the

steam pocket towel

over the steam pocket

frame and attach to

the inside of the

front side of the

steam pocket towel. (Fig. 12)

Fig. 12

NOTE:

If replacing the steam pocket

towel, make sure that the steam pocket

frame has been allowed to cool before

removing or attaching a new steam

pocket towel.

2. Bring the towel all

the way to the top

of the steam

pocket frame.

(Fig. 11)

Step 1: Before refilling the steam cleaner,

make sure that the unit is NOT

plugged in and has been allowed

to cool for fifteen (15) minutes.

Step 2: Plug the power cord in to an

electrical outlet and press the

steam switch on the hand grip to

the “ON” position to vent of any

residual steam that is in the boiler.

Step 3: Remove the power cord from the

electrical outlet and turn the steam

switch on the hand grip to the

“OFF” position.

Step 4: Place the unit on a flat, stable

surface. Slowly turn the safety

filler cap counter clockwise until it

is removed.

Step 5: Insert the funnel into the tank

opening and add 40 US Fl, Oz.

(1200 ml) of water. Place the

funnel in the tank opening as

illustrated in Fig. 5. The funnel has

been specially designed to show

when the water tank is full. When

water starts to come out of the

vent hole of the funnel, the tank is

full.

WARNING:

Allow unit to cool

for 15 minutes before refilling.

Use caution when opening the

Safety/Filler Cap as cap may

become hot during use and

escaping steam can cause

scalding.