Euro-Pro SC717XH - Manual (Page 6)

5
Operating Instructions
Caution: Always ensure the unit is unplugged from the wall receptacle prior to
filling or re-filling the water tank.
2. Simultaneously press down on the
safety cap and turn it counter-
clockwise until removed.
3. Place funnel in the tank and add
water. DO NOT overfill.
Maximum filling capacity is 300
mL (10 oz.) Replace the safety
cap by turning it clockwise until it
has tightened. Attach desired
accessory attachment.
Note: Heating time is approximately 4
to 5 minutes. Filling the boiler with hot
water will shorten heat up time.
4. Plug the unit into a standard 120
volt wall receptacle. The heating
light will then light up.
5. Allow approximately 4 to 5
minutes for water vapor to reach
its working temperature and
pressure.
6. At the start, some water may come
out of the nozzle (this is normal).
9. When finished using the steam
cleaner, unplug and allow to cool.
Follow the instructions in the
“Maintenance & Cleaning
Instructions” section.
Warning: DO NOT aim steam at any
live electrical components or
devices, such as electrical outlets.
Assembly and Using the Steamer
1. Before filling the steam cleaner,
make sure that the unit is NOT
plugged in. Also, slide the safety
trigger lock to the right to lock it.
(Fig. 1) To unlock this safety
feature, slide the trigger safety lock
to the left. (Fig. 2)
Locked
Fig. 1
Unlocked
Fig. 2
7. Grasp the handle firmly with one
hand and slide the trigger safety
lock to the left to unlock it.
8. Using your thumb, press down on
the trigger button to release the
steam (“ON” position). Turn the
variable steam adjustment in a
clockwise or counterclockwise
direction to change the amount of
steam released. To stop steam
from being released, let go of the
trigger button (“OFF" position).
Important Note: On the top of the
trigger button, there is a slide that can
be used to lock the trigger in the “ON”
position. To engage it, depress the
trigger button with your thumb and then
slide your thumb forward. (Fig. 3) To
release the lock and turn off the steam,
press down on the slide and pull it back,
then release the pressure on the trigger.
To avoid loss of steam while the unit
is heating, be sure that the steam
trigger is not depressed or locked in
the “ON” position prior to plugging
the unit in.
Locked in
the “ON”
position
Fig. 3
7. Screw safety cap back on the
appliance and plug appliance back
into wall outlet. Steam will start to
be produced as before.
Warning: This appliance is under
pressure. After every use, press trigger
button until all pressure has been
released before removing safety cap.
Important: DO NOT OVERFILL.
Maximum filling capacity is 300 ml.
(10 oz.).
Concentrator Nozzle
To attach the concentrator nozzle:
• Align the raised arrow on the larger
end of the concentrator nozzle with
the single white line on the ring of
the snout. (Fig. 5 & 6)
• Push the concentrator onto the
nozzle until it stops against the
appliance.
• To lock the concentrator nozzle in
place, turn it 90 degrees clockwise
so that the raised arrow mark aligns
with the two white lines on the ring
of the snout. (Fig. 6)
Operating Instructions
Important: Disconnect steam cleaner
from wall outlet before refilling. It is time
to refill your steam cleaner when there
is no more steam coming out of the
nozzle.
Warning: Because the water tank is
pressurized, use caution when opening
to refill. Always unplug the unit and let
the unit cool for 15 minutes before
opening the safety cap. Depress the
trigger button while you unscrew the
safety cap counter-clockwise.
Caution: When refilling the appliance
while it is still hot, the first drops of
water might squirt back. Use caution
when opening the safety cap.
Filling and Refilling the Steamer
1. Disconnect electrical power cord
from wall outlet.
2. Press down on the trigger button
until all pressure has been
released.
3. Wait for approximately 15 minutes
before carefully unscrewing the
safety cap.
4. Turn slowly a half turn counter-
clock wise and wait for the hissing
noise created by residual steam to
stop.
5. Unscrew the safety cap in the
counter-clock wise direction until it
is completely unscrewed and allow
it to cool.
6. Slowly pour water into the boiler
using the measuring cup and the
funnel. (Fig. 4)
Fig. 4
Funnel
Fig. 5
Larger End of the
Concentrator Nozzle
The ring of
the Snout
6
Align the
raised arrow
mark and the
single white
line.
Fig. 6