beautypg.com

Sealey BC301 User Manual

Pro trainer - bicycle, Bc301

background image

Maintain the trainer in good condition, replace or repair damaged parts. Use recommended parts only. Non authorised parts may be

dangerous and will invalidate the warranty.

Before use ensure that all nuts and bolts are tight and that moving and clamping parts are in good working order.

Place the Pro Trainer on a sound level surface offering adequate working clearance for its function. Keep the area clean, tidy and free from

unrelated materials. Ensure there is adequate lighting.

Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain long hair.

Keep children, pets and unauthorised persons away from the “workout” area.

7

Hard braking whilst using the Pro Trainer may cause excessive wear on cycle tyres and the trainer.

7

Never touch the wheels whilst they are in motion.

7

Never let go of the handlebars.

Always properly warm up before working out. Consult your physician before starting any exercise regime.

NOTE this Pro Trainer is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of

experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person

responsible for their safety. Children should be supervised to ensure they do not play with the appliance.

When not in use store the stand in a safe, dry, child proof area.

DO NOT exceed maximum load of 150kg.

Perfect for beginners or professionals who want to train all year round. Converts outdoor bicycle into an indoor trainer. Features a magnetic flywheel

unit with seven resistance settings, foldable frame, non-slip feet and quick release levers. Includes replacement hub skewer and front wheel block.

Model No: ........................................................................................BC301

Wheel Sizes: ........................................................................ 26” and 700C

Max Load ......................................................................................... 150kg

BC301 Issue: 2(I) - 16/12/14

© Jack Sealey Ltd

Original Language Version

INSTrUCTIoNS For:

PRO TRAINER - BICYCLE

ModEL No:

BC301

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT

CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL

INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these

instructions, and properly maintained, give you years of trouble free performance.

read instruction

manual

1. SAFETY

2. INTRODUCTION

3. SPECIFICATION

4. CONTENTS

1

11

4

6

3

2

13

9

8

10

12

7

Item

No

description Qty

1 “A”

Frame 1

2

Flywheel mechanism c/w cable

1

3

Quick release rod sub assembly

1-set

4

Clamp pedal sub assembly

1-set

5

Clamp cam follower

1

6

Pivot bolt 82 long (M8)

1

7

recessed plastic washer

2

8

C’sk screw M6 x 12

2

9

Stiff nut M8

2

10

Plain washer Ø8

3

11

open ended spanner 13/14 A/F

2

12

Hexagon key 4mm

1

13

Front wheel anti slip stand

1

fig.1

NOTE:

For best results make sure that your tyres are inflated to the maximum pressure allowed for your tyre. The maximum pressure will be

found moulded into the side wall of the tyre.

NOTE: To avoid a permanet “memory set” in the cycle tyre, when not using your Pro Trainer, either remove the cycle from the trainer or

adjust the trainer roller away from the tyre.

5.1

Assembly of the Pro Trainer.

5.1.1. The Pro Trainer PC310 comes partially assembled with the “A” frame in the folded position. Unfold the frame and place on a flat level

surface. The Pro Trainer can be adapted to most “solid” axle designs with hexagon nut axle fixing and the axle hollow bore “quick release

lever” design. The Pro Trainer can be adapted for two wheel sizes, 700C and 26”. The size of the wheel will be found moulded into the side

wall of the tyre.

5.1.2. The frame has two brackets for adapting the flywheel sub assembly. These brackets indicate fixing and pivot positions, position “A” is for size

700C wheel and position “B” is for the 26” wheel.

5.1.3. Thread the cam follower on to the clamp pedal as shown in fig.2.

5.1.4. Insert the cam follower into the twin cam track Pro Trainer mechanism as shown in fig.3 and fig.4.

5.1.5. Fit the sub-assembled clamp pedal and mechanism to the Pro Trainer frame brackets described in 5.1.2. and shown in fig.5. This is the most

involved part of the assembly process and could be eased with assistance to align pins with bracket holes, whilst supporting the flywheel.

5.2. Fitting the cycle to the Pro Trainer. (quick release hollow axle type)

5.2.1. release the quick release lever on the back wheel of your cycle and replace the axle with the quick release tightening rod item 3, supplied

with the Pro Trainer (fig.10). Tighten it an appropriate amount. Ensure the tapered end of your cycle’s tightening rod engages with the

tapered holding cup on the axle quick clamp; in the closed position.

5.2.2

. Tighten the “T” screw an appropriate amount to support the cycle and rider, then lock with the locknut.

5.2.3. Thread the cable for the handlebar resistance controls around your cycle and mount the resistance control to the handlebars. Make sure it

is in easy reach of the handlebars, and make sure the cable is clear of the wheels and pedals.

5.2.4. Place the anti-slip levelling stand under the front tyre.

5.2.5. Adjust the flywheel position to engage the tyre periphery. This will require trial and error rotation of the knob in fig.2.

5.2.5 Gently but firmly push the wheel quick clamp on the rear of the flywheel mechanism down to engage it with the rear wheel, (fig.6 & 8).

5.3. Fitting the cycle to the Pro Trainer. (solid rear axle types)

5.3.1. The cycle axle hexagon nuts will register with the counter bored and conical bored adjustable cups of the Pro Trainer, see fig.7. Ensure the

axle quick clamp is in the closed position. The quick release rod (item 3) is not required.

5.3.2. Tighten the “T” screw an appropriate amount to support cycle and rider; then lock with the locknut.

5.3.3. Thread the cable for the handlebar resistance controls around yourcycle and mount the resistance control to the handlebars. Make sure it

is in easy reach of the handlebars, and make sure the cable is clear of the wheels and pedals.

5.3.4. Place the anti-slip levelling stand under the front tyre.

5.3.5. Gently but firmly push the wheel quick clamp on the rear of the flywheel mechanism down to engage it with the rear wheel, (fig.6 & 8).

5.4. Operation

5.4.1.

Use the cycle’s own gears to achieve your desired level of effort.

5.4.2.

The resistance controller difference from 1 to 7 (fig.9) is only slight and can only be measured in energy used over a sustained period of

exercise. Remain in the chosen gear and choose position 7 for least resistance from the flywheel to position 1 for maximum resistance.

5.5. Removal

5.5.1. Remove the resistance controller (fig.9) from the handlebars.

5.5.2. Open the axle quick clamp on the top of the trainer by pressing up firmly yet gently, then loosen the securing nut on the opposite side.

remove the anti-slip levelling stand.

5.5.3. The cycle can now be removed.

5. ASSEMBLY

5

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: No liability is accepted for incorrect use of this product.

WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.

01284 757500

01284 703534

[email protected]

Sole UK Distributor, Sealey Group,

Kempson Way, Suffolk Business Park

,

Bury St. Edmunds, Suffolk,

IP32 7Ar

www.sealey.co.uk

fig.3

fig.4

fig.5

fig.2

700C Wheel size fixing positions “A”.

26” Wheel size fixing positions “B”.

700C setup

26” setup

Solid axle setup

Axle nut

in cup

Cable

Wheel Quick Clamp

Locknut

“T”

Screw

Hollow axle setup (cycle wheel removed)

Environmental Protection

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,

taken to a recycling centre and disposed of in a manner which is compatible with the environment.

When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)

into approved containers and dispose of the product and the fluids according to local regulations.

6.1 Storage

To store, carefully fold the Pro Trainer flat, and avoid storing other equipment on top of it. Keep all items together as in fig.10 indoors.

Wheel engage

adjustment knob

4

Cam

track

fig.6

fig.7

fig.8

fig.9

fig.10

resistance

controller

BC301 Issue: 2(I) - 16/12/14

© Jack Sealey Ltd

Original Language Version

BC301 Issue: 2(I) - 16/12/14

© Jack Sealey Ltd

Original Language Version

6,9,10

7,8

resistance

controller

Cable Adjustment