Sealey HVF18 User Manual
Page 2
Model No: . . . . . . . . . . . HVF18.V4
Fan Diameter:. . . . . . . 450mm(18")
Speeds: . . . . . . . . . . . . . . . . . . . . 3
Motor Power: . . . . . . . . . . . . .120W
Supply: . . . . . . . . . . . . . . . . . . 230V
Current:. . . . . . . . . . . . . . . . . . .0.6A
WARNING! Ensure that you read, understand and apply safety instructions in Section 1 before using fan.
4.1.
Check that the speed control is set to “0” (off) and then plug into the mains power supply and switch the power on.
4.2.
The fan features 3 speeds which are selectable using the switch located at the back of the fan above the motor.
1 or 2 settings will suit most needs, 3 is used for maximum air movement.
4.3.
Adjust the direction of the air flow by moving the base from side to side and tilting the fan up or down.
4.4.
When you have finished using the fan ensure you turn the speed control switch to "0” (off) and disconnect the fan from the mains
power.
WARNING! Ensure that the fan is disconnected from the mains power supply before attempting any of the following:
5.1.
Use a soft, damp cloth to clean the fan.
DO NOT immerse the fan in water and never allow water to drip onto the motor housing.
DO NOT use solvents, petroleum, paint thinner or other chemicals to clean the fan.
5.2.
To clean the fan blade, undo the five clips around the circumference, hinge up the front cover and clean the blade with a slightly damp
cloth. Replace the front grille and refit the five clips.
5.3.
Should the motor, switch or the power lead require service or maintenance contact your local service agent.
5.4.
When not in use place the fan in its original box or otherwise cover to protect from dust, and store in a safe, dry, childproof location.
High velocity fan suitable for movement of huge volumes of air. Carefully balanced and fully guarded blades provide quiet and safe operation.
Three-speed power selection and cradle stand allow precise control of air flow to exactly where it is needed. Fitted with BS approved plug.
Suitable for use in industrial, commercial, agricultural and automotive workshop and showroom applications.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email [email protected] or telephone 01284 757500.
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
WEEE Regulations
Dispose of this product at the end of its working life in compliance with the EU Directive on
Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed
of in an environmentally protective way. Contact your local solid waste authority for recycling information.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
2. INTRODUCTION
3. SPECIFICATION
4. OPERATION
5. CARE OF FAN
© Jack Sealey Limited
Original Language Version
HVF18.V4 Issue: 3(SP)- 19/1/15