Sealey RS131 - Manual (Page 2)

DO NOT use whilst under the influence of drugs, alcohol or intoxicating medication.
DO NOT leave the unit in a totally discharged state for an extended period of time as this may result in permanent damage.
DO NOT cross-connect the power leads from the RoadStart to the battery. Ensure that positive is to positive and negative is to
negative. Observe polarity indicator during connection.
Ensure that the unit is fully charged before storage.
1.3. ELECTRICAL SAFETY (with respect to mains chargers)
R WARNING! It is the user’s responsibility to check the following:
You must check the AC adaptor to ensure that it is safe before using. You must inspect the power supply lead, plugs and all
electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of
appropriate safety devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board.
We recommend that an RCD (Residual Current Device) is used with all electrical products. It is particularly important to
use an RCD with portable products that plug into an electrical supply not protected by an RCCB. If in doubt consult a qualified
electrician. You can obtain a Residual Current Device through your Sealey dealer. You must read and understand instructions
concerning electrical safety.
1.3.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested
by a qualified person, using a Portable Appliance Tester (PAT), at least once a year.
1.3.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance and the
safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.3.3. DO ensure that the insulation on all cables and the product itself is safe before connecting to the mains power supply.
1.3.4. DO ensure that cables are always protected against short circuit and overload.
1.3.5. DO regularly inspect power supply, leads, plugs for wear and damage and power connections to ensure that none is loose.
1.3.6. DO check product voltage is the same as power supply to be used and check that all fused plugs are fitted with the correct capacity
fuses.
2. INTRODUCTION
Composite case with moulded rubber protection, integral battery cable storage and carry handle. LED battery condition, polarity check and
charge indicators. Features independent on/off switch which allows the positive clamp to be connected with out the risk of sparking. Also fitted
with an integral Krypton work light for use at night. Fitted with 12Volt power socket that will accept any 12Volt device fitted with a cigarette
lighter type plug. Supplied with mains charger and double plug adaptor for in-car charging. RS132 has integral air compressor with pressure
gauge for accurately topping/pumping up tyres etc.
3. SPECIFICATION
Model: ................................................... RS131.V3 & RS132
Cold cranking amps: ......................................................200A
Peak amps: ....................................................................900A
Voltage: ............................................................................12V
Auxillary output: ...............................................................12V
Cable and clamp length: ............................................ 780mm
Built in compressor (RS132 only): .................................... yes
Max pressure: ............................................................... 80psi
Weight: ...............................(RS131.V3) 5.9kg (RS132) 6.5kg
4. PRODUCT FEATURES
(Key to figs. 1,2,3 & 4)
1) MOULDED RUBBER PROTECTION
2) HEAVY DUTY COPPER CABLE (POSITIVE+)
3) 12VDC OUTPUT SOCKET
4) 12VDC OUTPUT ON/OFF SWITCH
5) BATTERY CHECK BUTTON
6) LED CHARGE STATE INDICATORS
7) AC CHARGING SOCKET
8) KRYPTON WORK LIGHT
9) WORK LIGHT SWITCH
10) HEAVY DUTY COPPER CABLE (NEGATIVE+)
11) COMPOSITE CASING
12) COMPRESSOR CASING (RS132 only)
13) VALVE CONNECTOR (RS132 only)
14) NEGATIVE (-) BATTERY CLAMP (BLACK)
15) COMPRESSOR PRESSURE GAUGE (RS132 only)
16) COMPRESSOR ON/OFF SWITCH (RS132 only)
17)POSITIVE (+) BATTERY CLAMP (RED)
18)POSITIVE (+) BATTERY CLAMP SAFETY SWITCH
RS131.V3
RS132
fig.1
fig.2
RS131.V3 RS132 | Issue 4(I) 21/05/15 Original Language Version © Jack Sealey Limited