Environmental protection, Battery removal, Maintenance – Sealey CP2600 User Manual
Page 3
4. MAINTENANCE
4.1. CLEANING.
Keep the outer case of the wrench clean and free from grease.
DO NOT wash with water or use solvents or abrasives, use a damp cloth.
For any other service or maintenance, contact your authorised service agent.
4.2. LUBRICATION.
Periodically (or If the wrench has not been used for some time), remove the lubrication screw (fig.1.2) and inject some grease into
the impact mechanism, then replace the lubrication screw.
DO NOT overfill - a small amount each time should be sufficient.
WARNING! Ensure that you read, understand and apply the safety instructions before use.
3.2.
USING THE WRENCH.
3.2.1. Use only impact sockets which are specifically designed for use with an impact wrench. The use of normal chrome vanadium sockets
is dangerous, since these are more brittle and are liable to shatter.
3.2.2. Fit the socket to the wrench by snapping it onto the square drive (fig.1.1).
3.2.3. Fit the battery pack to the wrench by aligning the tongue on the battery with the groove in the housing and slide it into place. Ensure
that the battery pack is firmly located, you will hear an audible click when it has locked into position.
3.2.4. Select the required direction of rotation. To change direction, push switch (fig.1.3) to the left or right. Familiarise yourself with this
operation before use.
DO NOT attempt to change the direction of rotation whilst the trigger (fig.1.6) is depressed.
When the wrench is not in use, use the same switch to lock off the trigger by placing the switch in the middle position.
3.2.5. When tightening, release the trigger as soon as the impact sound is heard. Take care not to over-torque small fixings.
Note: On critical fixings, final tightening should be carried out using a torque wrench, setting it according to the product or the
vehicle manufacturer’s specifications.
3.2.6. To fit the side handle, lay the wrench on its side, so that the lubrication screw (fig.1.2) is facing upwards. Using a large screwdriver
remove the lubrication screw and replace it with the side handle ensuring that it is screwed fully home. Removal of the side handle is a
reverse of this procedure, ensuring that the lubrication screw is securely tightened.
Environmental Protection.
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycle centre and disposed of in a manner which is compatible with the environment.
WEEE Regulations.
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and
Electronic Equipment. When the product is no longer required, it must be disposed of in an environmentally protective
way. Contact your local solid waste authority for recycling information.
Rechargeable battery contains Lithium-ion (Li-ion). It is recyclable. Take to your local recycling centre to be disposed
of properly. Do not incinerate battery as it may explode when exposed to fire. Do not attempt to open battery pack.
Battery Removal.
•
For battery removal refer to section 3.1.1.
• Dispose of batteries according to local authority guidelines.
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of
products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance
scheme. Jack Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
Original Language Version
CP2600 Issue: 1 - 09/12/13
© Jack Sealey Limited