Sealey S0686 - Manual (Page 2)

3. OPERATINg INSTRUCTIONS
Input power: . . . . . . . . . . . . . . . . . . . . . . . . . . 230V - 50Hz
Motor: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .750W
No load speed: . . . . . . . . . . . . . . . . . . . . . . . . .0-2900rpm
Chuck capacity: . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13mm
Hammer action: . . . . . . . . . . . . . . . . . . . . . . . 0-43500bpm
Drilling capacity for steel: . . . . . . . . . . . . . . . . . . . . 10mm
Drilling capacity for masonry: . . . . . . . . . . . . . . . . . 13mm
Drilling capacity for wood: . . . . . . . . . . . . . . . . . . . 20mm
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4kg
Sound pressure level: . . . . . . . . . . . . . . . . . . . . . . . 101dB
Sound power level: . . . . . . . . . . . . . . . . . . . . . . . . .90dB.A
Vibration level:(Under load) . . . . . . . . . . . . . . . 13.422m/s ²
Vibration level (No load) . . . . . . . . . . . . . . . . . . . . 1.5m/s²
1. Trigger lock button
2. Trigger
3. Variable speed knob
4. Forward/Reverse switch
5. Drill/Impact switch
6. Chuck
7. Depth gauge
8. Side handle
9. Chuck key
3.1. PREPARING DRILL FOR USE.
3.1.1. Ensure the drill is switched off and unplugged from the mains power supply.
3.1.2. Fitting the side handle. (Fig.1.8) Fit side handle grip by placing the handle assembly over the chuck and onto the machine neck.
Secure by rotating the handle clockwise until it is tight and the handle can no longer be moved. To ensure a good grip in all
circumstances, the angle of the handle may be changed by rotating the handle grip anticlockwise until the handle assembly is loose.
Rotate the handle to the desired angle and retighten.
3.1.3 Fitting the depth gauge. (Fig.1.7) To fit the depth gauge loosen the side handle and pass the gauge through the handle
clamp to the required depth. Rotate the handle to the required angle. As the handle is tightened the depth gauge will also be gripped
firmly.
3.2. DRILL CONTROLS
3.2.1. ON/OFF Variable speed trigger. The drill has a variable speed control On/Off trigger (Fig.1.2) speed increases as the trigger is
depressed. Adjacent to the trigger is a button that can be used to lock the trigger in the ‘ON’ position for continuous drilling.
3.2.2 Trigger lock. (Fig.1.1) To lock ‘ON’, depress the trigger, push in and hold the button then release the trigger. Release the
lock-on button and the drill will continue running.
3.2.3 To release the lock, depress the trigger and the lock releases.
3.2.4 Power failure. If you have the lock-on feature engaged during use and the drill becomes disconnected from the power supply,
make sure that the lock is released, before reconnecting to the power supply.
 WARNING! Before connecting the drill to a power supply, ensure it is not in the lock-on position as this may result in
damage and personal injury. Depress the trigger to ensure release. DO NOT use the lock-on facility for jobs where the drill
may need to be stopped suddenly. ,
3.2.5. Maximum speed setting control. The variable speed trigger has a small rotating knob incorporated into it (Figs.1.3 & 2.3) which can
be used to control the maximum speed of the drill. When the knob is set to the maximum or + setting the trigger can be fully
depressed allowing the drill to turn at its maximum speed. As the knob is turned towards the minimum or - setting, the movement of
the trigger is restricted so that the drill will turn at a lower pre-set speed when the trigger is fully depressed. This facility is useful when
working with materials that should be drilled at a constant, lower speed.
3.2.6. The required speed will depend on the material and task in hand. The following may be used as a general guide.
a) Low speeds are recommended for hard materials, i.e. stone, ceramic, concrete, high tensile steel, and tasks such as starting
holes without centre punch, driving screws, mixing paint etc.
b) Medium speeds are suitable for plastics and laminates.
c) High speeds recommended for soft materials such as wood, aluminium, copper, bronze and brass.
 CAUTION: DO NOT run the drill at low to medium speeds for extended periods of time as this may cause drill to overheat.
To cool drill, run it without a load, at full speed, for a few seconds.
3.2.7 Direction of rotation. Select either forward or reverse rotation using the lever mounted directly above the trigger (Figs.1.4 & 2.4).
Select reverse by moving the lever towards the ‘L’ symbol and forward by moving the lever adjacent to the ’R’ symbol and the trigger
lock button.
 CAUTION: Do not attempt to change direction of rotation whilst the drill is still running.
3.2.8 Selection of hammer action / drilling. When using a masonry drill bit, the hammer action can be used to assist penetration into
concrete, stone and masonry. The hammer action selector is a large sliding ‘switch’ situated on top of the drill (Fig.3).
To select hammer action slide the selector to the left so that it is adjacent to the hammer symbol moulded on the side of the case.
To disable the hammer action slide the switch in the other direction to be adjacent to the drill symbol moulded on the casing.
3.3. DRILL OR TOOL BIT FITTING.
 WARNING! Unplug from the mains power supply before placing bit into chuck.
Adjust the chuck jaws to a point where the opening is slightly larger than the drill/tool bit (Fig.4.A) to be used. Also raise the front of
the drill slightly to stop the bit from falling out of the chuck jaws. Insert the drill/tool bit into the chuck as far as it will go. Place the
chuck key in one of the chuck holes and tighten the chuck fully by turning the chuck key clockwise (Fig 4.9).
2. TECHNICAL SPECIFICATION
Original Language Version S0686.V2 Issue: 1 - 23/10/12
Fig.2
© Jack Sealey Ltd
Fig.1