Sealey PC460 - Manual (Page 2)

 WARNING! Ensure you read, understand and apply Section 1
‘Safety Instructions’.
Reminder: DO NOT vacuum hazardous substances. Use of an
incorrect cartridge filter will invalidate your warranty.
4.1 ensure the machine is unplugged from the power supply. (fig.3.1)
4.2 remove the motor head assembly and fit the cartridge filter down over
the filter basket and push fully home. (fig.3.2) for better dust free
cleaning you can put the orange filter bag over the cartridge filter.
(fig.3.3)
4.3 the supplied dust bag can also be used when dry cleaning. (fig.3.4)
4.4 reposition the head onto the drum, and clip in place. (fig.3.5)
4.5 insert the larger end of the flexible hose into the front inlet on the
drum and lock in place. Push the required attachment/suction tube
onto the free end of the hose. (fig.3.6)
4.6 Plug in the power supply. (fig.3.7)
4.7 switch to the ‘on’ (position ‘i’). (fig.3.8)
4.8 When you have completed vacuuming, press the switch to ‘off’.
2. cONTeNTS AND SPecIFIcATIONS
2.1 carton content
2.1.1 carefully unpack the carton.
2.1.2 locate the two side clasps (fig.1.6) which hold the motor head
(fig.1.3) in place.
2.1.3 undo the clasps, remove the motor head and take out the items
in the drum.
2.1.4 check and identify each component as listed below. if anything
is missing or damaged please contact your supplier immediately.
2.2 Specification
motor: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1600W
drum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60ltr
supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V - 1ph
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16kg
Vac Accessories Ø: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38mm
filter - dry: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pc200cfl
4. DRY vAcUUm cLeANING
3. ASSemBLY
3.1 ensure the mains plug is disconnected. (fig.2.1)
3.2 undo clasps. (fig.2.2)
3.3 lift off the motor head assembly. (fig.2.3)
3.4 remove contents from inside the drum. (fig.2.4)
3.5 turn the drum upside down and insert the castors ensuring they
are pushed all the way in. (fig.2.5a)
3.5.1 insert the rear wheel shaft (n) into the rear support block. insert washer
(m) on the shaft, then insert rear wheel (K) on the shaft. insert the
lock pin (r) into the hole on the end of the shaft to lock the wheel. snap
the hub cap (o) on to the wheel. repeat the same steps at the other
end of the shaft. (fig.2.5b)
3.6 insert the frame into the drum (fig.2.6) to be used as the tool tidy frame
and handle to manoeuvre the vacuum.
3.7 for dry vacuum cleaning fit the cartridge filter supplied. (fig.2.7)
3.8 for dry vacuum cleaning the dust bags can also be used. (fig.2.8)
3.9 for wet vacuum cleaning use the foam filter supplied. (fig.2.9)
NOTe: Do not operate the cleaner without a cartridge filter fitted as
this will damage the machine and invalidate your warranty.
3.10 replace the motor head onto the drum. (fig.2.10)
3.11 Align up the motor head with the clasps and snap into place, by applying
pressure at the mid point of the clasps. (fig.2.11)
3.12 insert the large end of the hose into the front inlet of the drum and
lock in place by turning fully clockwise. (fig.2.12)
3.13 choose the desired nozzle and push it onto the suction tube.
fig.1
fig.3
Item Description
1 Handle
2 on/off switch
3 motor head assembly
4 filter basket
5 safety float valve
6 clasp
7 drum, (stainless steel)
8 Vacuum hose connection
9 drain plug
10 flexible vacuum hose
11 suction tubes
12 tool holder frame/handle
Item Description
13 combination brush
14 Air regulator handle
15 dust Bag
16 crevice nozzle
17 cartridge filter
18 cartridge filter bag
19 combination nozzle
20 foam filter
21 liquid drain hose
22 Brush tool
23 Attachment bag
fig.2
Original Language Version Pc460 issue: 2 - 22/10/09