beautypg.com

Filling the water tank, Operating your euro-pro steam cleaner – Euro-Pro STEAMER STEAM CLEANER EP63CH User Manual

Page 5

background image

Filling the Water Tank

Operating Your EURO-PRO Steam Cleaner

WARNING:

Always disconnect (unplug) the Garment Steamer from power

source before filling with water.

Your EURO-PRO Steamer Steam Cleaner is a very versatile tool. Used
correctly it will help make many household cleaning tasks faster and easier.
Be sure to carefully read all the information contained in this booklet before
using this appliance.

The Water Tank is the blue translucent tank at the end of the Garment Steamer.
See Fig. 2.

1. Remove the Tank by unscrewing it from the base unit by turning in a counter

clockwise motion.

2. Remove the Water Tank base by turning in a counter clockwise motion.

3. With cool water*, fill Water Tank completely and then replace water tank base

by turning in a clockwise motion until snug.

4. To reattach water tank to main unit, line up water tank fittings with fittings

receptacles on main unit. Push water tank in, then turn in a clockwise motion.

*Note: We suggest mixing distilled water or demineralized water with tap water -

1part tap water to 3 parts distilled or demineralized water. Doing so will

lengthen the life of the Steamer.

WARNING: With steam brush attachment assembled on unit - Do

not press Steam Push Button more than once per
second.
Pressing steam push button quickly may
cause hot water to accumulate between attachment and
main unit which could then leak through crevice and
burn user’s hand.0

CAUTION:

Never add anything except cool water or you will cause damage

to the heating element. Use water only, any other liquid may

be dangerous.

CAUTION

:

First usage may

require 6-10 rapid pushes on
steam push button before steam
exits. Keep pressing for a few
seconds until steam has
developed from first rapid
depressing of steam push
button, then you can continue
intermittent pressing of steam
push button.

CAUTION: Press steam
push button intermittently no
more than once every 1 or 2
seconds. Rapid pressing in
succession will cause water
leaking. Wait for steam
pressure to reduce before
pressing steam push button
again. By pressing
intermittently you will note a
rhythm for maintaining a
continuous flow of steam
without any water dripping
or leaking.

Power Cord

Before usage, remember to completely untangle or unwrap the full length of the

power cord.

Power Light/Indicator Light

The red light will illuminate when power is on - (unit is plugged into socket), green

light will go on and off during usage. Maximum temperature is achieved when green

light is illuminated. Before pushing steam push button the first time per usage, wait

until green light is illuminated. Following first usage, green light will go on and off. If

too much water is exiting steam holes, you are pressing steam push button too

rapidly. Stop pushing steam push button and wait for green light. Do not press

steam push button more than once per second or once per 2 seconds.

Note:

You may have some water exit on first burst. This is normal, just keep

pushing the steam button intermittently and you will obtain a continuous flow

of steam.

Note:

You may have some water exit on first burst. This is normal, just

keep pushing the steam button intermittently and you will obtain a

continuous flow of steam.

Steam Push Button

The steam push button is pumping water to the heating element. Continuous

steam can be attained if steam push button is depressed intermittently once every

one or two seconds. You will notice a rhythm can be maintained while pressing

steam push button which will maximize steam performance. Press steam push

button and wait until you see steam pressure reduced then press steam push

button again (approximately once every one or two seconds).

Important Note: After refilling or before each usage, it may take 6-10 presses on the

steam push button before steam will begin to exit. Press steam push button

repeatedly until first steam exists, then patiently press steam push button not more

than once every one or two seconds and eventually a momentum of steam will

develop. If you press too many times before steam exits, hot water may accumulate

and burn user’s hand if steam brush attachment is assembled on main unit.

5

4