Elta AL101 User Manual
Page 5
7
TECHNICAL
DA
T
A
Operational voltage:
230V~ 50Hz
Power input:
150 W
a
tt
Short-term operation:
3 Minutes
INSTRUCTIONS ON ENVIRONMENT PROTECTION
Do not dispose of this product in the usual household garbage at the end of its life
cycle; hand it over at a collection point for the recycling of electrical and electronic
appliances.
The symbol on the product, the instructions for use or the packing will
inform about the methods for disposal.
The materials are recyclable as mentioned in its marking. By recycling, material recycling or
other forms of re-utilization of old appliances, you are making an important contribution to
protect our environment.
Please inquire at the community administration for the authorized disposal location.
GUARANTEE AND
CUST
OMER
SER
VICE
Before delivery our devices are subjected to rigorous quality control. If, despite all care, damage has
occurred during production or transportation, please return the device to your dealer
. In addition to
statutory legal rights, the purchaser has an option to claim under the terms of the following
guarantee:
For the purchased device we provide 2 years guarantee, commencing from the day of sale. During
this period we will remedy all defects free of charge, which can be demonstrably attributed to
material or manufacturing defects, by repair or exchange.
Defects which arise due to improper handling of the device and malfunctions due to interventions
and repairs by third parties or the fitting of non-original parts, are not covered by this guarantee.
8
GB
GB
GB
GB
•
Connect the power plug
(10)
to a suitable power outlet.
•
Set the On/Of
f switch
(2)
to either
1
,2
or
3
.
•
Now you can press the safety switch
(1)
.
The cutting knife
(8)
will start to rotate. Once you
release the safety switch, the device will be turned of
f.
Careful!
As the device is powered, the
caster of the device will cause the knife to need about 2 seconds before it comes to a complete
stop.
•
T
he cutting sled
(6)
can be steadily and lightly pushed back and forth.
•
Should the rotation speed of the knife slow down while cutting the food, do not continue to push
the food against the knife
(8)
. W
ait a moment for the knife to regain its normal speed.
•
Once you are finished, always set the On/Of
f switch
(2)
back to the
0
position. Pull the plug.
•
Ti
p
: When you wish to cut very thin slices, moisten the knife
(8)
with a moist cloth.
This prevents
the food from sticking to the knife. While moistening the knife, the power plug should not be
connected to a power outlet!
•
Important note
: Never use the device for more than
3 consecutive minutes
. Before operating
the device again,
let it cool down to room temperature
first.
CARE AND
MAINTENANCE
•
Please also observe the
safety advice.
•
Pull the power plug.
•
Remove the leftover tray
(4)
and the sled
(6)
.
T
o
do so, slide the sled
(6)
along the footing
(7)
until
the arrows are aligned. Now you can lift the sled
(6)
and remove it.
The leftover tray
(4)
and the
sled
(6)
can be cleaned with lukewarm water and some dishwashing detergent.
•
The device can be cleaned with a moist cloth after use and should be thoroughly dried with
another cloth afterwards.
•
Never use abrasive or aggressive detergents or utensils.
•
Never use gasoline or thinners to clean the device.
•
F
or easy cleaning, the knife
(8)
can be removed as follows:
T
urn the wing screw of the knife
locking clockwise. Hold the knife by the screw and carefully lift it out. Clean the knife
(8)
with
running water and some dishwashing detergent. For best results, use a dish mop.
The inside
actuation parts may not be exposed to water
.
Therefore, thoroughly dry the knife
(8)
.
•
Attention!
The cutting knife
(8)
is very sharp!
After cleaning the device, reinsert the knife and the
lock it in place by screwing the wing screw of the knife locking anticlockwise.
•
S
tore the device and its accessories, where they are inaccessible for children.
elta GmbH
Carl-Zeiss-Str
. 8
63322 Rödermark