Euro-Pro 372H - Manual (Page 17)

(Model EP 377 and 374 only)
(Model 373/372/372H)
2.Lower the foot and sew slowly until the desired length is sewn,
then stop the machine at
1. Set the pattern selector at . Then pass the needle thread
throughthe opening in the buttonhole foot and draw both needle
and bobbin threads to the left side. Turn the balance wheel
towards you until the needle comes to the point
3. Raise the needle and set the selector at . Then sew
several stitches of bar tack until the needle is at point
5. Raise needle and set the selector at then sew several
stitches of final bar tack. Stop the machine with the needle at
point . To lock threads, set the pattern selector at B (zero
point of zigzag width). And sew a few stitches.
4. Raise the needle and set the selector at then sewthe
right side of buttonhole the same length as the left side of
buttonhole. Stop the machine at
6. Cut thebuttonhole open carefully using a seam ripper, taking care
not to damage the bar tacks.
1. Set the pattern selector at Then pass the needle thread
through the opening in the buttonhole foot and draw both of
needle and bobbin threads to the right side. Turn the balance
wheel towards you until the needle comes to the point
2. Lower the foot and sew slowly until a desired length is sewn,
then stop the machine at
3. Raise the needle and set the selector at then sew
several stitches of bar tack until the needle is at point
4. Raise the needle and set the selector at then sew the
left side of buttonhole just as the same length as the right side of
buttonhole. Stop the machine at
5. Raise the needle and set the selector at then sew several
stitches of final bar tack. Stop the machine with the needle at
point
6. Cut the buttonhole open carefully using a seam ripper, taking
care not to damage the bar tacks.
Note: To make a heavier buttonhole, sew twice by repeating the
same procedure.
(2).
(3).
(4).
(5).
(1).
(1).
(2).
(3).
(4).
(5).
SEWING BUTTONHOLES (Model 377 and 374)
¡°¡±
¡ ° ¡ ±
¡ ° ¡ ±
¡ ° ¡ ±
¡ °
SEWING BUTTONHOLES (Model 373/372 /372H)
15
S E WING ZIP P E R S
M odel 377 Model 373/372/372H M odel 374
zipper foot
Pattern selector
Presser foot
S titch length dial 1 to 4
M ( ) 1-3( )
1 to 4
A ( )
R a is e the foot a nd the ne e dle to its highe s t pos ition by turning
the ba la nc e whe e l towa rds you. R e pla c e the foot with the z ippe r
foot.
1. P in or ba s te the z ippe r ta pe to the fa bric a nd pla c e the work-
pie c e in pos ition unde r the foot.
A tta c h s na p on z ippe r foot s o tha t the ne e dle pa s s e s on its
le ft ha nd s ide .
* W he n s ta rting s e wing, both ne e dle a nd bobbin thre a ds e nds
s hould be put a wa y unde r the foot.
2. S e w on the right s ide of the z ippe r by guiding Z ippe r te e th
a s c los e a s pos s ible to the ne e dle drop. B e fore the foot re a c he s
the s lide r on the z ippe r ta pe , ra is e the foot a nd ope n the
z ippe r by ke e ping the ne e dle in the fa bric .
L owe r the foot a nd s e w on the re ma ining of the s e a m,
3. To s e w the le ft s ide z ippe r c ha nge pos ition of foot to bring
the foot to the le ft s ide of the ne e dle . S e w on in the s a me
wa y a s you did on the right s ide of z ippe r.
Z ippe r foot
E le me nts
ta pe
F a bric
E le me nts
S lide r
F ia . 1
S lide r
E le me nt
Z ippe r foot N e e dle
F a bric
Ta pe E le me nt
E
n
g
lis
h
zipper foot zipper foot
¡°¡±
¡°¡±
¡°¡±
¡°¡±