Electrolux ELECTRIC WHEELED Rotary Lawnmower - Manual (Page 5)

Safety Precautions
12. Keep hands and feet away from the cutting means at
all times and especially when switching on the motor.
13. Do not tilt lawnmower when the motor is running,
except when starting and stopping. In this case, do
not tilt more than absolutely necessary and lift only
the part which is away from the operator. Always
ensure that both hands are in the operating position
before returning the appliance to the ground.
14. Do not put hands near the grass discharge chute.
15. Never pick up or carry a mower when it is
operating or still connected to the mains supply.
16. Remove the plug from the mains :
-
before leaving the mower unattended for any period;
- before clearing a blockage;
- before checking, cleaning or working on the appliance;
- if you hit an object. Do not use your lawnmower
until you are sure that the entire lawnmower is in
a safe operating condition;
- if the lawnmower starts to vibrate abnormally. Check
immediately. Excessive vibration can cause injury.
Maintenance and storage
1. Keep all nuts, bolts and screws tight to be sure
the lawnmower is in safe working condition.
2. Check the grassbox/grassbag frequently for wear
or deterioration.
3. Replace worn or damaged parts for safety.
4. Only use the replacement blade, blade bolt,
spacer and impeller specified for this product.
5. Be careful during adjustment of the lawnmower
to prevent entrapment of the fingers between
moving blades and fixed parts of the machine.
Wheel Assembly
1. Select one of the holes in the mounting plate and
note it as the other wheels will need to be
adjusted to the same position. (A1)
2. Locate the fixing bolt through hole in the hub
cap, wheel and selected hole in mounting plate.
3. Turn the wheel hub in a clockwise direction until the
wheel assembly is securely located to the deck. (A2)
Lower Handles - 37cm (B1, B2)
1. Locate 2 screws into the holes in the handles.
2. Using a pozidrive screwdriver, secure the screws
into the lower handles, ensuring the point of the
screw stays inside the handle. (B1)
3. Insert lower handles, with screws attached, into
the deck and fully tighten screws. (B2)
Note: The screw will form its own thread
Lower Handles - 42cm (C1, C2)
1. If your product has Cutting Height with levers,
ensure the lever is at the Highest Cut Height
before following steps 2 & 3.
2. Insert each side of the lower handles into deck as
shown in Fig C1.
3. Push each side of the handle firmly down until it
is located securely into the deck (C2).
4. Insert screw through the washer and into holes
using a pozidrive screwdriver and tighten fully into
deck as shown in Fig C2.
Lower Handles
Upper Handles
1. The upper handle should be fixed to the lower
handle using whichever type of kit is provided as
shown in Figs D1, D2 and D3.
2. Fit the cables to the handles with the cable ties
provided, making sure the cables are not trapped
between the upper and lower handles.
Grassbox Assembly - 37cm.
1. Insert the grassbox handle into the top of one of
the grassbox halves. Press firmly down and
forward until the handle clicks into position (E)
2. Turn the grassbox half over and insert screw into
hole (as illustrated in fig E) and tighten fully.
3. Locate grassbox upper into grassbox lower. (F)
Align clips, ensure all clips are correctly located.
4. Clip the two halves together.
5. Ensure all clips are securely connected.
Grassbox Assembly - 42cm
1. Insert the grassbox handle into the top of one of
the grassbox halves. Press firmly down and
forward until the handle clicks into position (E)
2. Turn the grassbox half over and insert screw into
hole (as illustrated in fig E) and tighten fully.
3. Position the two grassbox halves together and press
each location point (G1-A) into position without fully
connecting the clips. When the location points are
matched correctly firmly press the grassbox together
until all clips are securely connected.(G1-B, G2)
37cm, 42cm
1. To attach the grassbox to your lawnmower, lift the
safety flap (H) and make sure the discharge chute
is clean and free from debris.
2. Locate fully assembled grassbox onto 2 location
points at the rear of the deck. (H)
3. Locate safety flap onto the top of the grassbox.
Ensure the grassbox is securely located.
• Removal is the reverse procedure.
• Please Note Ensure no gap remains between
the safety flap and the grassbox/bag
• Where grass collection is not required you can
use the lawnmower without the grassbox/bag.
Ensure the safety flap is fully closed
Grassbox Assembly
ENGLISH - 2
Cable Restraint (J1 ,J2, J3)
1. Attach cable restraint above switchbox (J1).
2. Form loop in mains cable and push the loop
through (J2).
3. To secure, position loop over the hook and pull
cable back through the slot. (J3)
Cable Restraint (K1, K2, K3)
1. Connect female extension cable connector to the
back of the switchbox. (K1)
2. Form loop in mains cable and push the loop
through the slot. (K2)
3. To secure, position loop over the hook and pull
the cable back through the slot.(K3)
Cable Restraint