Operating instructions – Euro-Pro EP603H User Manual

Page 6

OPERATING INSTRUCTIONS

4. Hold the HEPA filter

by the edges and vigorously

“TapClean” the HEPA Filter

dirty side down on a hard,

flat surface until no more

dust is observed falling out

from between the pleats of

the filter. (Fig. 11) We

recommend washing the HEPA filter

once a month or when suction

appears to be reduced. Let the HEPA

filter air dry completely for 24 hours.

5. Rinse the non-woven pre-filter and let

air dry completely for 24 hours.

6. Insert the non-woven pre-filter.

7. Reinstall the HEPA filter in the

vacuum.

8. To separate the debris screen from

the dust cup, hold the dust cup in one

hand and turn the

dust cup cover counter

clockwise and pull apart.

To clean the debris

screen, we recommend

that you rinse it under

lukewarm running water

to remove the dirt that

accumulates on it, but always allow it

to completely air dry before inserting

back into the vacuum. (Fig. 12)

Fig. 12

Warning:

Always unplug the

unit from electrical outlet before

opening the Dust Cup (container).

Warning

After each Use -

Always remove Filter Assembly

and the Dust Cup Cover with

the Debris Screen, then

vigorously “TapClean” HEPA

Filter and clean Debris Screen

and Non-Woven Pre-Filter until

no more dust can be removed.

2. To empty the dust

cup container,

press on the trap

door release button

that is on the back

side of the dust cup

container. (Fig. 8)

Dust

Cup

Release
Button 2

Dust

Cup

Release
Button 1

Fig. 8

Fig. 11

Fig. 7

HEPA
Filter

Non-Woven
Pre-Filter

Fig. 10

Fig. 9

3. The HEPA filter is

located underneath the

dust cup container. (Fig.9)

Remove the Non-Woven Pre-Filter.

(Fig. 10) Remove the HEPA filter, hold

the edges and pull it out slowly.

Emptying the Dust Cup Container

and Cleaning / Changing the Non-

Woven Pre-Filter, HEPA Filter &

Debris Screen

WINDING & UNWINDING THE

POWER CORD

Your vacuum cleaner includes

a power cord which is

automatically retractable.

To extend your power cord,

pull from side and extend

to desired length up to

the yellow mark on the

power cord. (Fig. 5)

Do not pull the power

cord beyond the red

mark. When vacuuming

is finished, first switch

off power and disconnect plug from

electrical outlet. Then press on cord

rewind button. If the cord does not fully

retract, pull it out again and then press

on cord rewind button.

Warning:

Hold the plug when

rewinding the cord. Do not allow the

cord to whip when rewinding.

USING THE UNIT AS A HAND
VACUUM

• Press the telescopic tube release

button to remove the telescopic tube.

(See Fig. 2 page 4)

• Press the floor brush release button to

remove the floor brush. (See Fig 3

page 4)

• Attach the shoulder strap to the

shoulder strap attachment point.

(Fig. 6)

• Attach the crevice tool or the dusting

brush to the end of the hose.

Crevice Tool

For radiators, crevices, corners,

baseboards and

between cushions.
Dusting Brush
The dusting brush is

used for the furniture,
venetian blinds,
books, lamp shades
and shelves.

= OFF

= ON

USING THE UNIT AS AN UPRIGHT

• Unwind the power cord and plug into

the 120V outlet.

• Push down on the

locking button to adjust

the height of the

telescopic handle.

NOTE:

When vacuuming

deep pile carpets or hard

to vacuum carpets,

lower the angle of

the telescopic

handle (see

illustration at right)

for easier maneuverability.

Low

Warning

: After extended use, the body

of the vacuum cleaner may become hot.

When using the unit with the shoulder

strap, the unit will touch the body of the

user. Therefore, make sure that the unit

body is cool before you use with the

shoulder strap. If during use, the vacuum

gets too warm, allow it to cool before

continuing to use.

Intelli-Sense

Filter Monitor

Fig. 5

Fig. 6

Yellow

Red

Important:

Do NOT use the vacuum

without the HEPA filter in place.

IMPORTANT, Please Note: The

“TapClean” HEPA Filter will stop most of

the tiniest dust particles from re-entering

the air you breathe. In fact it stops 99.97%

of all particles as small as 0.3 microns -

many times smaller than a human hair!!!

Because of this incredible filtration

performance, the HEPA Filter will quickly

accumulate, inside the white filter folds,

many fine dust particles that are difficult to

see but which will eventually block or

reduce your suction power - if not cleaned

properly.

ON/OFF SWITCH

• The On/Off switch has two different

positions.

• Push on the "I" side to turn the

vacuum ON.

• Push on the "O" side to turn the

vacuum OFF.

1. To remove the dust cup container,

first press on the dust cup release

button (1) that is located on the dust

cup handle and at the same time

press on the dust cup release button

(2) that is on the side of the upper

housing. (Fig. 7) Then pull the dust

cup container out.

When the Intelli-Sense

Filter Monitor

lights up, it means that the dust cup is
full, the HEPA filter, non-woven pre-filter
or debris screen need cleaning. You
must empty the dust from the dust cup
and clean the HEPA filter, non-woven
pre-filter, or debris screen.
Also check the hose and attachments to
see if they are blocked with any debris.
If they are, unblock them.