Parkside PBZS 20 A1 - Manual (Page 2)

- 7 - - 8 - - 9 - - 10 - - 11 - - 12 -
IAN 102532
KOMPERNASS HANDELS GMBH
BURGSTRASSE 21
44867 BOCHUM
DEUTSCHLAND / GERMANY
www.kompernass.com
Version des informations ·Stand der Informationen
Last Information Update: 06 / 2014
Ident.-No.: PBZS20A1-052014-1
Bei stationär eingesetzten Bürsten immer unterhalb
der Bürstenmitte arbeiten (siehe Abb. 1).
Sind höhere Geschwindigkeiten und stärkerer An-
pressdruck erforderlich, müssen aggressivere Bürsten
verwendet werden.
Das wird erreicht durch:
− größere Drahtstärke;
− geringere Besatzlänge;
− oder durch anderen Bürstenbesatz
(gezopft anstatt gewellt).
Optimierung des Bürsteneinsatzes
Der gewünschte Bürsteneff ekt muss sich innerhalb von
wenigen Sekunden einstellen.
Bürsteneff ekt ist zu gering:
− Drehzahl erhöhen (max. Drehzahl beachten!);
− größeren Bürstendurchmesser verwenden;
− kürzere Besatzlänge wählen;
− stärkeren Drahtbesatz wählen bzw. andere
Bürstentypen.
Bürsteneff ekt ist zu stark:
− Drehzahl reduzieren;
− Anpressdruck verringern;
− größere Besatzlänge wählen;
− dünneren Drahtbesatz wählen bzw. andere
Bürstentypen.
■ GB
Importeur
KOMPERNASS HANDELS GMBH
BURGSTRASSE 21
44867 BOCHUM
GERMANY
www.kompernass.com
Service
Service Deutschland
Tel.: 0800 5435 111 (Kostenfrei aus dem
dt. Festnetz/Mobilfunknetz)
E-Mail: [email protected]
IAN 102532
Service Österreich
Tel.: 0820 201 222 (0,15 EUR/Min.)
E-Mail: [email protected]
IAN 102532
Service Schweiz
Tel.: 0842 665566 (0,08 CHF/Min.,
Mobilfunk max. 0,40 CHF/Min.)
E-Mail: [email protected]
IAN 102532
Erreichbarkeit Hotline:
Montag bis Freitag von 8:00 Uhr – 20:00 Uhr (MEZ)
Congratulations!
With your purchase you have decided in favour of a
high quality product. Read these safety and operating
instructions attentively before using the appliance
for the fi rst time and retain these instructions for later
reference. Also, pass them on to whoever might
acquire the appliance at a future date.
Safety instructions
♦ Do not exceed the specifi ed maximum rotation
speed!
♦ Wear close-fi tting protective clothing and eye
protection!
♦ Use a machine guard, if available!
Safety instructions as per DIN EN 1083-2
♦ Brushes must not be fi tted onto machines whose
rotation speed lies above the maximum permitted
brush speed.
♦ Damaged brushes may not be used.
♦ Rust discoloration or other signs of chemical or
mechanical change to the mounting material can
cause premature failure of the brush.
♦ Brushes must be stored in suitable racks, bins or
boxes such that they are protected against the
following eff ects:
1) high humidity, heat, water or other liquids that
could cause damage to the brushes;
2) Acids or vapours of acids, which could cause
damage;
3) Temperatures that are so low that they could
lead to condensation when the brushes are
relocated to an area with higher temperatures;
4) Deformation of any brush component.
Recommendations for use
Only the wire tips do the work (see Fig. 1).
Prerequisite is the exertion of light pressure while
brushing (see Fig. 1).
Increased pressure does not improve the result,
instead, it reduces the service life of the brush and
requires higher input power (see Fig. 2).
Fig. 1:
Correct operation Fig. 2:
Incorrect operation
For stationary inserted brushes, always work below
the middle of the brush (see Fig. 1).
Should higher rotation speeds and greater pressure be
required, then more aggressive brushes must be used.
This is achieved by:
− larger wire gauge;
− reduced braid length;
− or through another brush braid
(plaited instead of corrugated).
Optimization of the brush
attachment
The desired brush eff ect must be apparent within
a few seconds.
Brush eff ect is insuffi cient:
− increase rotation speed
(pay heed to max. rotation speed!);
− use a larger brush diameter;
− select a shorter braid length;
− select a stronger wire braid, or another
type of brush.
Brush eff ect is too forceful:
− reduce the rotation speed;
− reduce the pressure;
− select a longer wire braid;
− select a thinner wire braid, or another
type of brush.
Importer
KOMPERNASS HANDELS GMBH
BURGSTRASSE 21
44867 BOCHUM
GERMANY
www.kompernass.com
Service
Service Great Britain
Tel.: 0871 5000 720 (£ 0.10/Min.)
E-Mail: [email protected]
IAN 102532
Hotline availability:
Monday to Friday 08:00 - 20:00 (CET)
2
IB_102532_PBZS20A1_LB2.indd 2 IB_102532_PBZS20A1_LB2.indd 2 04.06.14 12:22 04.06.14 12:22