Grass Valley K2 Media Client Quick Start Guide for SD-00 models Nov.18 2008 - Manual

K2 Media Client
Quick Start Guide
For SD-00 models
Before you begin, unpack the following items...
071-8453-02 July 3, 2007
...and locate the documentation you need.
K2 Media Client
Power cords Release Notes
System Software CD
Licenses and
Warranties
Rack slides
Recovery CD
Documentation CD
usss usssusss usss usssusss
rass all roup
rass all roup rass all roup rass all roup
usss usssusss usss usssusss
rass all roup
rass all roup rass all roup rass all roup
K2 SDI MEDIA CLIENT
!
RS-422
Port 3
Port 4
SCSI
RS-422
Port 1
Port 2 10Bt
100Bt
1000Bt
Pu sh Pu sh Pu sh Pu sh Pu sh Pu sh
GPIO ! SDI CH 1
IN OUT
SDI CH 2
IN OUT
SDI CH 3
IN OUT
SDI CH 4
IN OUT
OUT OUT OUT OUT
IN
LTC CH 1 LTC CH 2 LTC CH 3 LTC CH 4 UNUSED UNUSED
IN IN IN
AES/EBU CH 1
IN OUT 1-2
3-4
1-2
3-4
1-2
3-4
1-2
3-4
1-2
3-4
1-2
3-4
1-2
3-4
1-2
3-4
AES/EBU CH 2
IN OUT
AES/EBU CH 3
IN OUT
AES/EBU CH 4
IN OUT
REF
COMPOSITE LOOP
THRU
1. Make cable connections and, if necessary, configure network
2. Power on 3. Install control point software 4. Make remote connection
Connect video
inputs and outputs
(supports embedded audio). Connect audio
inputs and outputs, if
using AES/EBU audio.
Keyboard/Mouse VGA monitor
If using LTC, connect
inputs and outputs as
needed per channel. Connect
power cords.
GigE Port 3
GigE Port 4
GigE Port 1
GigE Port 2
Each channel (CH1, CH2, CH3, CH4) can
be both an input (record channel) and an
output (play channel). You can connect
video/audio IN and OUT to each channel, as
appropriate for your intended use.
Bi-directional channels
You must add external storage
models to a K2 Storage System.
Refer to the K2 Storage System
Instruction Manual and the K2
Media Client System Guide for
complete procedures.
External storage
K2-01AA00015
Press both bezel-release buttons and flip down front bezel.
Press the standby switch to power on.
At first startup, End User License Agreements appear
on the screen. Accept the agreements to continue.
Identify
the following:
Control point PC
K2 System
Software CD
Insert CD, open the Control
Point folder and run setup.exe.
Choose a network-connected
PC as your control point.
Service
LED Standby
switch Power
LED Serial
number
Power LED goes on and stays on.
Service LED stays off. Startup
processes complete in approximately
two minutes and the K2 Media Client is
ready for remote connection and
operation.
Follow on-screen instructions,
clicking
Next , Install , and
Finish .
Normal startup sequence
Microsoft Windows XP
Professional, Service Pack 2
(U.S. version)
Pentium 4 or higher class
processor, 2 GHz or greater
Minimum 512 MB RAM,
1 GB recommended
400 MB hard disk space
Graphics acceleration with at
least 128 MB memory
Microsoft .NET Framework
1.1 (available on K2 System
Software CD)
MS XML 4, Service Pack 2
(available on K2 System
Software CD)
PC System requirements
AppCenter
A
er ter
pCente
te er
Click
Add .
Enter the K2 Media Client hostname or IP
address. The default hostname is the chassis
serial number (e.g. K2-01AA00015). Refer to
step 2. Power on to locate the serial number.
Select the channels to control
from this control point PC.
Click OK and OK to save
settings and close.
Click OK .
Continue with Quick Start procedures on the reverse side.
Control point PC
Refer to K2 Media Client
System Guide for RS-422
connections. Connect other cables as needed.
Refer to the K2 Media Client
System Guide for complete cabling
and network instructions.
Access the Windows logon dialog.
Use a locally connected keyboard,
mouse, and monitor. If not locally
connected, use Windows Remote
Desktop Connection with default
settings as above.
Logon with the default Windows
administrator account:
Username: administrator
Password: adminK2
In Network Connections, for
internal storage models configure
Control Connection #1 . For
external storage models,
configure
Control Team .
Use default settings – DHCP is
enabled and the chassis serial
number is the hostname. If
supported by your network, you
can use these defaults.
Configure network settings – If
necessary, power up the K2 Media
Client and do the following:
Quick Start networking options
PS2 USB
Note: You can skip ahead if you are:
Using the Grass Valley control point PC. Skip to step 4.
Accessing the K2 Media Client locally only. Skip to step 5.
1
2
3
1
2
3
1
2
3
3
Logon to AppCenter with the
default K2 administrator account.
- Username: K2admin
- Password: K2admin 2
Open the AppCenter shortcut. 1
4
6
5
7
Fam ily o f XP Ser ies
Fam ily o f XP Ser ies
Fam ily o f XP Ser ies
Fam ily o f XP Ser ies
Fam ily o f XP Ser ies
Fam ily o f XP Ser ies Gra ss V alle y Gro up
Release
Notes
Documentation path to install
K2 Media Clients with internal storage
VIDE O PR ODU CTIO N CE NTER VIDE O PR ODU CTIO N CE NTER VIDE O PR ODU CTIO N CE NTER VIDE O PR ODU CTIO N CE NTER VIDE O PR ODU CTIO N CE NTER VIDE O PR ODU CTIO N CE NTER
VIDE O PR ODUC TION CEN TER VIDE O PR ODU CTIO N CE NTER VIDEO PROD UCTI ON CE NTER VIDE O PR ODU CTIO N CE NTER VIDEO PRO DUC TION CEN TER VIDE O PR ODU CTIO N CE NTER
VIDE O PR ODU CTIO N CE NTER VIDE O PR ODU CTIO N CE NTER
Fam ily o f XP Ser ies
Fam ily o f XP Ser ies
Fam ily o f XP Ser ies
Fam ily o f XP Ser ies
Fam ily o f XP Ser ies
Fam ily o f XP Ser ies Gra ss V alle y Gr oup
VIDEO PRO DUC TION CEN TER VIDE O PR ODU CTIO N CE NTER VIDEO PRO DUC TION CEN TER VIDE O PR ODU CTIO N CE NTER VIDE O PR ODU CTIO N CE NTER VIDE O PR ODU CTIO N CE NTER
VIDEO PROD UCTIO N CEN TER VIDE O PR ODU CTIO N CE NTER VIDE O PR ODU CTIO N CE NTER VIDE O PR ODU CTIO N CE NTER VIDE O PR ODU CTIO N CE NTER VIDE O PR ODU CTIO N CE NTER
VIDE O PR ODU CTIO N CE NTER VIDE O PR ODU CTIO N CE NTER
System
Guide Quick Start
Guide
K2 Q uick Th is d oc um en t hel ps you con nec t ins tal l K 2 to pla y a nd rec ord
Documentation path to install
K2 Media Clients with (external) K2 Storage System
Fam ily o f XP Ser ies
Fam ily o f XP Ser ies
Fam ily o f XP Ser ies
Fam ily o f XP Ser ies
Fam ily o f XP Ser ies
Fam ily o f XP Ser ies Gra ss V alley Gro up
*Release
Notes
VIDE O PR ODU CTIO N CE NTER VIDE O PR ODU CTIO N CE NTER VIDE O PR ODU CTIO N CE NTER VIDE O PR ODU CTIO N CE NTER VIDE O PR ODU CTIO N CE NTER VIDE O PR ODU CTIO N CE NTER
VIDEO PRO DUC TION CEN TER VIDE O PR ODU CTIO N CE NTER VIDEO PROD UCTI ON C ENTER VIDE O PR ODU CTIO N CE NTER VIDE O PR ODU CTIO N CE NTER VIDE O PR ODU CTIO N CE NTER
VIDE O PR ODU CTIO N CE NTER VIDE O PR ODU CTIO N CE NTER Fam ily o f XP Ser ies
Fam ily o f XP Ser ies
Fam ily o f XP Ser ies
Fam ily o f XP Ser ies
Fam ily o f XP Ser ies
Fam ily o f XP Ser ies Gra ss V alle y Gr oup
VIDE O PR ODU CTIO N CE NTER VIDE O PR ODU CTIO N CE NTER VIDE O PR ODU CTIO N CE NTER VIDE O PR ODU CTIO N CE NTER VIDE O PR ODU CTIO N CE NTER VIDE O PR ODU CTIO N CE NTER
VIDEO PROD UCTI ON C ENTER VIDE O PR ODU CTIO N CE NTER VIDEO PRO DUC TION CEN TER VIDE O PR ODU CTIO N CE NTER VIDEO PRO DUC TION CENT ER VIDE O PR ODU CTIO N CE NTER
VIDE O PR ODU CTIO N CE NTER VIDE O PR ODU CTIO N CE NTER
System
Guide Quick Start
Guide Storage System
Instruction Manual
*Storage Release Notes and Cabling Guide packed with RAID primary chassis
K2 Q uick Th is do cu me nt help s y ou conn ect ins tal l K 2 to pla y a nd reco rd
*Cabling
Guide
K2 Q uick Th is d oc um ent hel ps you con nec t ins tal l K 2 to pla y a nd rec ord
Note: Add external storage models to a K2 Storage
System before proceeding.
Levels 2 and 3 (non-redundant):
-Port 1 - Control network
-Port 2 - Media (iSCSI) network
Levels 2R and 3R (redundant):
-Port 1 & 3 - Control network
-Port 2 - Media (iSCSI) network A
-Port 4 - Media (iSCSI) network B
Port 1 - Control network
Port 2 - FTP/Streaming
Ports 3 & 4 - Not used
Internal storage models:
External storage models:
GigE connections