Euro-Pro VPW49HA - Manual (Page 3)

SAFETY & WARNING INSTRUCTIONS
WARNING
Do not use pressure that exceeds the
operating pressure of any of the parts (hoses,
fittings, etc.) in the pressurized system.
Ensure that all equipment and accessories are
rated to withstand the maximum working
pressure of the unit.
WARNING
Explosion hazard.
• NEVER spray flammable liquids or use
pressure washer in areas containing
combustible dust, liquids or vapors.
• NEVER operate this machine in a closed
building or in or near an explosive
environment.
WARNING
Do not spray electrical apparatus or wiring.
• NEVER disconnect the high pressure
discharge hose from the machine while
the system is pressurized. To depressurize
the machine, turn the power and water
supply off, then press the gun trigger 2-3
times.
• NEVER permanently engage the trigger
mechanism on the gun.
• NEVER operate the machine without all
the components properly connected to
the unit (handle, gun/lance assembly,
nozzle, etc.).
WARNING
• NEVER store the pressure washer outdoors
or where it could freeze. The pump will be
seriously damaged.
• Release trigger when changing from high to
low pressure modes. Failure to do so could
result to damage to the nozzle.
• This unit must always be used in the
horizontal position.
CAUTION
Keep hose away from sharp objects. Bursting
hose may cause injury. Examine hoses
regularly and replace if damaged. Do not
attempt to mend a damaged hose.
DANGER
EXTENSION CORDS
Equipment damage.
• ALWAYS turn water supply "ON" before
turning the pressure washer "ON". Running
pump dry causes serious damage.
• Do not operate the pressure washer with
the inlet water screen removed. Keep
screen clear of debris and sediment.
• NEVER operate pressure washer with
broken or missing parts. Check equipment
regularly and repair or replace worn or
damaged parts immediately.
• Use only the nozzle supplied with this
machine.
• Never leave the lance unattended while
the machine is running.
• Never attempt to alter factory settings.
Altering factory settings could damage the
unit and will void the warranty.
• Always hold gun and lance firmly when
starting and operating the machine.
• NEVER allow the unit to run with the
trigger released (OFF) for more than one
minute. Resulting heat buildup will
damage pump.
If using an extension cord, use only grounded,
three wire extension cords that are in good
condition. Use only extension cords that are
intended for outdoor use. These extension
cords are identified by a marking "Acceptable
for use with outdoor appliances; store indoors
while not in use." Use only extension cords
having an electrical rating not less than the
product. Do not use damaged extension
cords. Examine extension cord before using
and replace if damaged. Do not abuse
extension cord and do not pull on the cord to
disconnect. Keep cord away from heat and
sharp edges. Always disconnect from the
receptacle before disconnecting the product
from the extension cord.
Note: Do not use 16 or 18 AWG extension
cords on this product.
DANGER
Failure to follow these instructions can result
in serious injury, including death.
WARNING
To reduce the risk of electrocution, keep all
connections dry and off the ground. Do not
touch the plug with wet hands.
Allowable Length
Extension Cord
25 ' 50 ’
14 AWG YES NO
12 AWG YES YES
2
TROUBLE SHOOTING
PROBLEM POSSIBLE REASON POSSIBLE SOLUTION
PRESSURE
WASHER WILL
NOT START WHEN
THE ON/OFF
SWITCH IS IN THE
"ON" POSITION
1. Electrical socket is faulty or
breaker has tripped.
2. Voltage is inadequate.
3. GFCI has tripped.
4. Power cord is not plugged in.
1. Check plug, socket, fuses,
breaker.
2. Check that the voltage is
adequate.
3. Reset/Try another electrical
outlet.
4. Plug in power cord.
PUMP DOESN'T
REACH
ADEQUATE
PRESSURE OR
CAVITATES 1. Water intake filter is clogged.
2. Pump is drawing air.
3. Diameter of garden hose is
too small.
4. Water supply is restricted.
1. Remove and clean water
intake filter.
2. Tighten connections/bleed
system.
3. Replace with 3/4 inch
garden hose.
4. Check hose for kinks or
leaks, open tap fully.
PRESSURE
WASHER HAS OR
WILL NOT
MAINTAIN
PRESSURE
1. Excessive air in waterline and
pump.
2. Water supply is restricted.
1. Turn unit and water supply
off/Bleed system/Hold
trigger down. Allow water to
flow through the pump for
30 seconds.
2. Check hose for kinks or
leaks, open tap fully.
PRESSURE
WASHER MAKES
EXCESSIVE NOISE
1. Air intake is blocked.
2. Water intake filter is dirty.
1. Clean the air intake vents.
2. Check & clean filter.
MOTOR DOES
NOT RUN
CONTINUOUSLY
WHEN TRIGGER IS
SQUEEZED/
MOTOR BUZZES
WHEN TURNED
ON BUT DOES
NOT
START/MOTOR
STOPS RUNNING
WHILE UNIT IS IN
USE
1. Net voltage is lower than
suggested. 1. Check that the voltage is
adequate.
9