ARM Electronics C600BCDNVFIR - Manual (Page 2)

ARM Electronics Roseville, CA 95678 1. 855.388.7422 www.armelectronics.com
Rev. 071111
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER(OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
ISO14001
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER(OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
ISO14001
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER(OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
ISO14001 The lightning flash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
INFORMATION - This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules & CE Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
their own expense.
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
Do NOT use power sources other than those specified.
This installation should be made by a qualified service person
and should conform to all local codes.
• This camera should be installed by qualified personnel only
• There are no user serviceable parts inside
• Do not disassemble this camera other than to make initial adjustments
• Use a UL approved regulated 24 volt AC or 12 volt DC power supply
• Use appropriate low voltage power cable to prevent fire or electrical shock
• Please insure that your installation area can support the weight of the camera
• Do not use a strong or abrasive detergent when cleaning the camera
• Do not point the camera to direct into sunlight
• Do not install camera in places where humidity is high
• Do not install near cooling or heating device
• Do not expose internal components to rain or moisture
Precautions for use
Please handle this camera carefully
Do not install the camera in
extreme temperature conditions.
Do not touch the front lens of the
camera.
Do not expose the camera to rain
or spill liquids on it.
Do not install or use the camera in an
environment where the humidity is high.
Do not install or use the camera in an
environment where the humidity is high.
Never keep the camera pointed
directly at strong light.
Do not expose the camera to
radioactivity.
Do not install the camera under
unstable lighting conditions.
Do not drop the camera or subject
it to physical shocks.
Only use the camera under conditions
where temperatures are between
-10°C and +50°C. Be especially careful to
provide ventilation when operating under
high temperatures.
This is one of the most important parts of
the camera. Be careful not to leave
fingerprints on the lens cover.
If it gets wet, wipe dry immediately.
Liquids can contain minerals that
corrode the electronic components.
It can cause malfunctions to occur.
If exposed to radioactivity the CCD
will fail.
Severe lighting change or flicker can
cause the camera to work improperly.
Severe lighting change or flicker can
cause the camera to work improperly.
NOTE
* If the camera is exposed to
spotlight or object reflecting
strong light, smear or
blooming
may occur.
* please check that the power
satisfies the normal
specification before
connecting the camera.
1 | 2 |
3 | 4 |
Do not install the camera in
extreme temperature conditions.
Only use the camera under conditions
where temperatures are between -14° F
~ 122° F. Be especially careful to provide
ventilation when operating under high
temperatures.
Do not install or use the camera in an
environment where the humidity is high.
Do not install or use the camera in an
environment where the humidity is high.
Do not install the camera under
unstable lighting conditions.
Severe lighting change or flicker can
cause the camera to work improperly.
Do not touch the front lens of the
camera.
This is one of the most important parts
of the camera. Be careful not to leave
fingerprints on the lens cover.
Never keep the camera pointed
directly at strong light.
It can cause malfunctions to occur.
Do not drop the camera or subject
it to physical shocks.
Housing damage can compromise
weatherproof ratings.
Do not expose internal components
to rain or moisture.
If it gets wet, wipe dry immediately.
Liquids can contain minerals that
corrode the electronic components.
Do not expose the camera to
radioactivity.
If exposed to radioactivity the CCD
will fail.
NOTE
•
If the camera is exposed to spotlight or object reflecting strong light,
smear or blooming may occur.
•
please check that the power satisfies the normal specification before
connecting the camera.
C600BCDNVFIR
600 Line WDR Bullet Camera with 80’ IR Range
DAY/NIGHT, 2DNR, D-WDR, OSD, CABLE MGMT, 2-8.12mm LENS
SAFETY INSTRUCTIONS
•
This camera should be installed by qualified
personnel only.
•
Do not disassemble this camera, There are no user-
serviceable parts inside.
•
Use a UL approved regulated 24 volt AC or 12 volt DC
power supply.
•
Use appropriate low voltage power cable to prevent
fire or electrical shock.
•
Please insure that your installation area can support
the weight of the camera.
HANDLING INSTRUCTIONS
•
Do not use a strong or abrasive detergent
when cleaning the camera.
•
Do not point the camera directly into sunlight.
•
Do not install camera in places where humidity is high.
•
Do not install near a cooling or heating device.
•
Do not expose internal components to rain or moisture.
PRECAUTIONS FOR USE