Smithco Super Star X-Treme Gas 43-000-x (sn 43001 – 43056) Parts & Service Manual - Manual (Page 51)

49
Accessories
42-136 60" SAND PLOW PART LIST
REF# PART# DESCRIPTION QUANTITY
1 42-092 Lift Assembly (includes Ref# 20) 1
2 HNTL-12-13 Lock Nut 1 /
2
- 13 4
3 HB-38-16-350 Bolt 3 /
8
- 16 x 3 1 /
2 (part of main frame) 2
HWL-38 Lock Washer 3 /
8
2
HN-38-16 Nut 3 /
8
- 16 2
4 HCP-12-150 Clevis Pin 1 /
2
x 1 1 /
2
2
5 27-049 Left Pusher Bar 1
6 HB-38-16-300 Bolt 3 /
8
- 16 x 3 2
HW-38 Washer 3 /
8
4
HNTL-38-16 Lock Nut 3 /
8
- 16 2
7 HB-12-13-200 Bolt 1 /
2
- 13 x 2 2
8 HMB-12-14 Machine Bushing 1 /
2
x 14GA 8
9 80-006 Rod End 4
HNJ-12-20 Jam Nut 1 /
2
- 20 4
10 27-073 Lift Rod 2
11 35-011 Aluminum Plow Blade 60" 1
12 HB-38-16-100 Bolt 3 /
8
- 16 x 1 2
HW-38 Washer 3 /
8
2
HWL-38 Lock Washer 3 /
8
2
HN-38-16 Nut 3 /
8
- 16 2
13 HB-12-13-300 Bolt 1 /
2
- 13 x 3 2
HNTL-12-13 Lock Nut 1 /
2
- 13 2
14 HB-38-16-100 Bolt 3 /
8
- 16 x 1 5
HWL-38 Lock Washer 3 /
8
5
HN-38-16 Nut 3 /
8
- 16 5
15 35-012 Wear Blade 1
16 27-050 Right Pusher Bar 1
17 HHP-18 Bridge Pin 1 /
8
2
18 42-094 Rod 1
19 42-093 Lift Handle 1
20 18-221 Flange Bushing 2
21 HMB-34-14 Machine Bushing 3 /
4
- 14GA 1
22 HP-18-150 Cotter Pin 1 /
8
x 1 1 /
2
1
23 15-019 Grip 1
24 HB-12-13-200 Bolt 1 /
2
- 13 x 2 2
INSTALLATION INSTRUCTIONS
1. Assemble pusher bars (Ref 5 and 16) to plow (Ref 11) using hardware (Ref 12 & 13). There are 2 holes to bolt
the hardware in. Using hole closest to the blade will result in a shallow cut, whereas using the hole furthest from
the blade will result in a deeper cut. The slot on the pusher bar is for fine tuned adjustment.
2. Assemble the lift assembly (Ref 1) to the main frame using the two studs that are under the frame and below the front
of the console.
3. Attach the lift handle (Ref 19) to the lift assembly using cotter pin and machine bushing (Ref 21 & 22). Using rod and
yoke (Ref 18 & 9) attach the handle to the lift assembly.
4. Put rod ends (Ref 9) onto lift rods (Ref 10) with jam nut first. Adjust to equal lengths. Bolt lift rods to lift arms with ball
joints to the outside. Bolt from outside with the
1 /
2
" machine bushing between rod end and lift arm and the 1 /
2
-13 nylon
lock nut on the inside. Use (Ref 7) hardware.
5. Slide plow under machine and connect to machine. Use clevis pin and bridge pin (Ref 4 & 17).
6. Lift up the plow. Using the top hole in the lift rod as a starting point hook on the pusher bars. Use (Ref 6) hardware. The
three holes in the lift rods are for adjusting the hand lever. The top hole moves the lever forward and holds the blade
with the most clearance. Each hole down moves the lever to the rear of the machine and decreases blade clearance
by approximately one inch.
7. For fine tuning of blade height off ground twist rod end (Ref 9) on rod (Ref 18). Twisting the rod end out will increase
down pressure. Twisting the rod end onto the rod will decrease down pressure.