Smithco Super Rake 13-55х (sn 6450 – 6594/1200-1301) Parts & Service Manual - Manual (Page 55)

53
Accessories
13-505 LIFT ASSEMBLY PARTS LIST
REF# PART# DESCRIPTION QUANTITY
1 HCP-12-150 Clevis Pin 1 /
2
x 1 1 /
2
1
2 HB-716-14-150 Bolt 7 /
16
-14 x 1 1 /
2
2
3 13-004 Cooler Bracket 1
4 Main Frame ( Part of Trap Rake )
5 HSSQ-38-16-200 Square Head Set Screw 3 /
8
- 16 x 2 1
HN-38-16 Nut 3 /
8
- 16 1
6 HB-38-16-125 Bolt 3 /
8
-16 x 1 1 /
4
1
7 HW-38 Washer 3 /
8
3
8 HNTL-38-16 Lock Nut 3 /
8
-16 1
9 13-146 Attachment Lift 1
10 HNTL-716-14 Lock Nut 7 /
16
-14 2
11 HNTL-38-16 Lock Nut 3 /
8
1
12 HB-38-16-200 Bolt 3 /
8
-16 x 2 1
13 18-166 Adapter 3
14 18-292 Elbow with Orifice 1
15 13-292 Hydraulic Cylinder 1
16 HP-18-150 Cotter Pin 1 /
8
x 1 1 /
2
1
18-164 Hydraulic Hose 2
14-253 Seal Kit for 13-292
INSTALLATION INSTRUCTIONS
13-505 Lift Assembly comes standard on 13-550 Super Rake optional on 13-551 Super 2.
1. Raise and block machine so you can get under it safely.
2. Replace bolts (Ref 2) located toward rear of machine with two new 7 /
16
- 14 x 1 1 /
2
bolts. Place attachment lift (Ref 9)
under frame with cylinder tabs on left side of machine and the arms pointing to rear. Use two 7 /
16
- 14 lock nuts to hold
in place.
3. Lower machine to ground.
4. Connect cylinder (Ref 15) to frame (Ref 4) using clevis pin (Ref 1) and cotter pin (Ref 16) with cylinder ports pointing
up.
5. Bolt rod end of cylinder in top hole of attachment lift (Ref 9) using bolt (Ref 12), two washers (Ref 7) (one on each side
of cylinder rod) and locknut (Ref 11). Bolt head should be to the outside.
6. Before making the attachment adjustment, be sure tire pressure in all tires is the same. On a level surface, lower
attachment to ground until one side touches. On the right side of the attachment lift there is an adjustment bolt and
screw (Ref 5 and 6) to level the arms.
7. If adjustable side is high, adjust square head set screw (Ref 5) to lower attachment so that it is level with the ground. If
adjustable side is low, adjust the square head set screw to raise attachment level to the ground. Tighten lock nut.
8. Put bolts (Ref 6) with one 3 /
8
washer through arm and bracket. The bolt head should be to the outside of machine, with
lock nut on inside.
9. Put elbow (Ref 14) with orifice into port on clevis end of cylinder (pointing to rod end) and tighten. Put one adapter
(Ref 13) in other port and tighten.
10. Remove two plugs from valve and replace with two adapters. Tighten both adapters.
11. To connect hoses, first connect tube end of hose to adapter on rod end of cylinder. Leave it loose. Route hose to
bottom port of valve. Tighten both ends of hose. Then connect other hose (hose end) to elbow in cylinder and tube end
to top port of valve. Tighten both ends of the hose.
12. Assemble valve handle to valve.
13. Sit on seat and start machine. Work the valve so lift will raise and lower. Do this until air works out and cylinder
operates smoothly. At same time check for hydraulic leaks. Shut engine off.
14. Check hydraulic oil tank level. The level should be about 2" to 2 1 /
2
" from top of the tank when fluid is cold. Use SAE
10W-40 API Service SJ or higher motor oil.