Edid learning explained, Installation, Installation diagram – Smart Avi DVS-200 User Manual
Page 2: Technical specifications, Resolutions, Input/output signal, Supported by the internal edid configuration, Prepairing system cat6 cable
PC or MAC
Local Monitor
Plasma TV
Plasma TV
CAT6-STP
CAT6-STP
DVI-D
DVI-D
5V
5V
5V
DVS200
Transmitter
DVXRX200
Reciever
DVXRX200
Reciever
Technical Specifications
Input/Output Signal
#
n
i
P
l
a
n
g
i
S
#
n
i
P
l
a
n
g
i
S
1
-
2
a
t
a
D
S
.
D
.
M
.
T
6
1
t
c
e
t
e
D
g
u
l
P
t
o
H
2
+
2
a
t
a
D
S
.
D
.
M
.
T
7
1
-
0
a
t
a
D
S
.
D
.
M
.
T
3
d
l
e
i
h
S
4
/
2
a
t
a
D
S
.
D
.
M
.
T
8
1
+
0
a
t
a
D
S
.
D
.
M
.
T
4
-
4
a
t
a
D
S
.
D
.
M
.
T
9
1
d
l
e
i
h
S
5
/
0
a
t
a
D
S
.
D
.
M
.
T
5
+
4
a
t
a
D
S
.
D
.
M
.
T
0
2
-
5
a
t
a
D
S
.
D
.
M
.
T
6
k
c
o
l
C
C
D
D
1
2
+
5
a
t
a
D
S
.
D
.
M
.
T
7
a
t
a
D
C
D
D
2
2
d
l
e
i
h
S
k
c
o
l
C
S
.
D
.
M
.
T
8
c
n
y
S
.t
r
e
V
g
o
l
a
n
A
3
2
+
k
c
o
l
C
S
.
D
.
M
.
T
9
-
1
a
t
a
D
S
.
D
.
M
.
T
4
2
-
k
c
o
l
C
S
.
D
.
M
.
T
0
1
+
1
a
t
a
D
S
.
D
.
M
.
T
1
1
d
l
e
i
h
S
3
/
1
a
t
a
D
S
.
D
.
M
.
T
1
C
d
e
R
g
o
l
a
n
A
2
1
-
3
a
t
a
D
S
.
D
.
M
.
T
2
C
n
e
e
r
G
g
o
l
a
n
A
3
1
+
3
a
t
a
D
S
.
D
.
M
.
T
3
C
e
u
l
B
g
o
l
a
n
A
4
1
r
e
w
o
P
V
5
+
4
C
c
n
y
S
z
r
o
H
g
o
l
a
n
A
5
1
D
N
G
5
C
d
n
u
o
r
G
g
o
l
a
n
A
PIN 17
PIN 1
PIN 24
PIN 8
C 4
C 1
C 2
C 5
C 3
EDID Learning Explained
The Display Data Channel (DDC) is a digital connection
between a computer display and a graphics adapter
that allows the display to communicate its specifications
to the adapter.
The Extended Display Identification Data (EDID) is a
data structure provided by a computer display over the
DDC to describe its capabilities to a graphics card.
The DVS200 does not continue the DDC across the
CAT6 links and contains its own EDID at the video
source input. Therefore, the EDID on the DVS200 is
used in place of the actual monitor’s EDID. In order for
the computer to output at the correct resolutions and
refresh rates for a specific monitor, the DVS200 must be
loaded with the monitor’s EDID.
On power-up the DVS200 reads and stores the EDID
of the DVI monitor connected to the local loopback
port. If the local loopback port is disconnected during
power-up, the stored EDID will not be modified.
Installation
1. Turn off computer and monitor.
2. Connect DVI male to male cable between the
computer and the transmitter.
3. Connect monitor or projector to the local loopback
DVI port on the transmitter.
4. Turn on the monitor.
5. Plug in one of the power transformers and
connect it to the transmitter.
6. Remove the monitor from the local loopback
DVI port on the transmitter and connect it
to the DVI port on the receiver.
7. Connect a shielded CAT6 cable between port 1
on the transmitter and port 1 on the receiver.
8. Plug in the other power transformer and connect
it to the receiver.
9. Turn on the computer.
Installation Diagram
Resolutions
Supported by the internal EDID configuration
640 x 480
85 Hz
800 x 600
85 Hz
1024 x 768
85 Hz
1152 x 870
75 Hz
1280 x 768
75 Hz
1280 x 960
60 Hz
1280 x 1024
60 Hz
1600 x 1200
60 Hz
1920 x 1080
60 Hz
Resolution
Refresh Rate
Pair 1 Pins 1 & 2
Pair 2 Pins 3 & 6
Pair 3 Pins 4 & 5
Pair 4 Pins 7 & 8
Connectors:
RJ-45
Capacitance:
14 pf/ft (46.2 pf/m)
Conductor Gauge: 24 AWG
Impedance:
100 +/- 15 ohms
4 - Pair, (stranded) Foil Shielded
Prepairing System CAT6 Cable
Prepairing System CAT6 Cable
Prepairing System CAT6 Cable
Prepairing System CAT6 Cable
Prepairing System CAT6 Cable