Smart Avi HDCIR - Manual (Page 2)

Introduction
The
HDC-IR
range
of
products
allow
the
extension
of
Infra
R
ed
control
signals using single CAT5 UTP
(category
5,
unshielded twisted pair) cable. The
HDC-IR
is
the
first
product for this application.
Features
Uses
easy
to
install,
inexpensive
CAT5.
Output
reaches
up
to
1000
feet
(300
m).
Sends
IR
and Power signals over CAT5
Bi-directional IR. High
ground
loop
immunity.
Built-in
lightning,
power
surge
and
transient
protection. Remote
Units
come
with
Buffered
Outputs.
Compact
Enclosure.
Optional
power
supply
for
remote
unit.
Fully
compliant
with
standard
modulated
IR
a
n
d
the
latest
IRDA.
Fully
transparent
path
for
all
protocols
and
data
transfers.
What’s
in
the
box?
HDC-IR Please
check
the
contents
of
the
package
before
beginning
installation.
Installation
Diagram
yt
Q
m
et
I
n
oi
t
pi
r
cs
e
D
1 1 1 1
D
E
L-
MS
E
Y
E-
MS
2
Installation
Instructions
Operating
Instructions
Once
installation
is
completed,
verify
that
the
power
is
present
at
all
devices
in
the
system.
The
peripheral
devices
should
be
ready
for
use.
s
dr
a
d
n
at
S
g
ni
ri
W
5
T
A
C
#
niA
P8
6
5
AI
T/
AIB
E8
6
5
AI
T/
AI
E
e
1p
ir
ts
n
e
er
g
hti
w
eti
he
Wp
ir
ts
e
g
n
ar
o
hti
w
eti
h
W
n
2e
er
g
dil
os
r
o
e
pi
rt
s
eti
h
w
hti
w
n
e
er
G
e
g
n
ar
o
dil
os
r
o
e
pi
rt
s
eti
h
w
hti
w
e
g
n
ar
O
3
e
pi
rt
s
e
g
n
ar
o
hti
w
eti
h
W
e
pi
rt
s
n
e
er
g
hti
w
eti
h
W
e
4u
l
b
dil
os
r
o
e
pi
rt
s
eti
h
w
hti
w
e
ul
B
e
ul
b
dil
os
r
o
e
pi
rt
s
eti
h
w
hti
w
e
ul
B
e
5p
ir
ts
e
ul
b
hti
w
eti
he
Wp
ir
ts
e
ul
b
hti
w
eti
h
W
6
e
g
n
ar
o
dil
os
r
o
e
pi
rt
s
eti
h
w
hti
w
e
g
n
ar
O
dil
os
r
o
e
pi
rt
s
eti
h
w
hti
w
n
e
er
G
n
7w
or
b
dil
os
r
o
e
pi
rt
s
n
w
or
b
hti
w
eti
h
W
n
w
or
b
dil
os
r
o
pi
rt
s
n
w
or
b
hti
w
eti
h
W
n
8w
or
b
dil
os
r
o
e
pi
rt
s
eti
h
w
hti
w
n
w
or
B
n
w
or
b
dil
os
r
o
e
pi
rt
s
eti
h
w
hti
w
n
w
or
B
Connecting the IR
Use the Diagram for the IR connection.
Connecting the Transmitter 1. Connect the IR LED to the IR window on the source device. 2. Connect power supply to the unit. Observe LED lighting up indicating power present. Connecting the Receiver Connect IR LED to the IR window on the souce device. 2. Connect the IR Eye to the Receiver. 3. Observe LED lighting indicating power present. Connect the Transmitter to the Receiver Connect the transmitter to the receiver using Category 5 UTP cable (Purchased separately). The CAT 5 UTP cable, if purchased in bulk, will be wired using 568A or 568B wiring standard. Once connected, check that the power LEDs on both the receiver and the transmitter are on, IR status LED is on and RX LED is flashing when Remote control is used indicating that communication is in progress.
HDC-IR-TX HDC-IR-RX PS12VD1A
IR Transmitter IR Receiver IR Emitter IR Eye “Optional” Power supply12VDC1A
Supports any IR Remote Control.
HDC-IR can be used 2 ways,
1. enabling the remote side to control the DVD, or any other source device. (the IR eye would be connected at the remote). 2. enabling the source side to turn off or on the remote TV/Monitor (the IR eye would be connected at the source.