beautypg.com

RLE Cable Construction User Manual

Cable construction guide, Supplies for installation, Contents of this kit sensing cable assembly

background image

Cable Construction Guide

Thank you for purchasing the SeaHawk sensing and non-sensing cable construction
kit (part number CCK-LD). This guide describes how to use this kit to construct cables
in the length required for your application.

If you need further assistance, contact RLE Technologies at [email protected] or
call us at 800.518.1519,

Supplies for Installation

Sold Separately

SeaHawk Leak Detection Sensing Cable, LD-SC-xx

SeaHawk Non-Sensing Cable, LD-NSC-xx

Cable Connector Kit, CCK-LD

Pin Crimp Tool, SCPC

Cable Stripper, SCCS

Contents of This Kit

Sensing Cable Assembly

(Orange Cable, RLE #1227)

1

Spool the cable to the desired length (1’ minimum to 100’ maximum).

2

Slide the 3/8 x 1/2 inch (Part# 1151) shrink tube over each end of the
sensing cable. Shrink it with a heat source 1 inch from each end.

3

Using dikes or needle nose pliers, untwist the orange carrier above the
shrink tube. Trim both ends to 3/4”.

4

Split the orange carrier as far as the shrink tube and strip them 3/8”.

Note: If you are not going to put the pins or sockets on at this time, leave the

strip plug on the wires.

5

Crimp the connector sockets (RLE Part #1295 & 1300) on one side (slide
back the black braiding to expose approximately 1/8” of the silver wire
before crimping
). Crimp the connector pins (RLE Part #1296 & 1299) on the
opposite side (slide back the black braiding to expose approximately 1/8” of
the silver wire before crimpin
g).

6

Slide the grips (2) (Part #2409) and boots (2) (Part #2410) over both ends
as shown below. Snap the sockets into the plug (Part #1298) and the pins
into the receptacle (Part #1294) as follows: Orange wire with writing in pin 1,
Orange wire with-out writing in pin 4, The black braided wires as they fall
into pin 2 & 3 respectively.

7

Screw the grips onto the plug and receptacle, and tighten by hand. Screw
the boots onto the grips, and tighten by hand.

v 1.2

(09/2014)

© Raymond & Lae Engineering, Inc. 2011. All rights reserved. RLE

®

is a registered trademark and Seahawk™, Falcon™, and

Raptor™ are trademarks of Raymond & Lae Engineering, Inc. The products sold by Raymond & Lae Engineering, Inc. are
subject to the limited warranty, limited liability, and other terms and conditions of sale set forth at rletech.com.

66101-2, RLE Part #3257 (Blue Dot)
(2 per sensing cable) Sockets

66105-2 RLE Part #3254 (Blue Dot)
(2 per sensing cable, 4 per non-sensing cable) Sockets

66099-2, RLE Part #3256 (Blue Dot)

(2 per sensing cable) Pins

66103-2, RLE Part #3255 (Yellow Dot)
(2 per sensing cable, 4 per non-sensing cable) Pins

206060-1, RLE Part #1298
Plug

206153-1, RLE Part #1294
Receptacle

207490-1, RLE Part #2410
Grip (2 per cable)

207489-1, RLE Part #2409
Boot (2 per cable)

Shrink Tubing

3/8 x 1/2 (2 per sensing cable)
RLE Part #1151

3/16 x 1 (2 per non-sensing cable),
RLE Part #2505

1/4 x 1 (2 per non-sensing cable),
RLE Part #2550

Part #1295 (2) small black wires - Crimp
Part #1300 (2) large orange wires - Crimp

Part #1296 (2) small black wires - Crimp
Part #1299 (2) large orange wires - Crimp

Part #1298 Plug

Part #2409 Grip

Part #2410 Boot

Part #2409 Grip