Marantz AV8003 - Manual (Page 62)

CONNECTIONS
SETUP
BASIC
OPERA
TION
REMOTE
CONTROLLER
TROUBLESHOOTING
OTHERS
NAMES AND
FUNCTION
ADV
ANCED
OPERA
TION
59
ENGLISH
CHECKING THE XM PRESET CHANNEL
The preset channel can be checked on the on screen
display.
3.
4. 3.
4.
2. 2.
(Using the remote controller)
1. Switch the remote controller to TUNER mode.
2. Press the < / > button until 002 is display.
3. Press the P-INFO button. to view a list of tuner
preset channeI on the on screen display.
4. If there are 10 or more preset channel, Press
the P-lNFO button. again.
X M P R E S E T L I S T
N O . 1 X M 0 1 0 X X X X X X X X X X
N O . 2 X M 0 1 1 X X X X X X X X X X
N O . 3 X M 0 1 5 X X X X X X X X X X
N O . 4 X M 0 2 2 X X X X X X X X X X
N O . 5 X M 1 2 5 X X X X X X X X X X
N O . 6 X M 0 0 1 P r e v i e w
N O . 7 X M 0 0 1 P r e v i e w
N O . 8 X M 0 0 1 P r e v i e w
N O . 9 X M 0 0 1 P r e v i e w
N O . 1 0 X M 0 0 1 P r e v i e w
Note:
• The preset channel indication disappears in about 5
sec.
PRESET SCAN
3.
5. 3.
5.
2. 2.
5. 5.
1. Switch the remote controller to TUNER mode.
2. Press the < / > button until 002 is displayed.
3. press the P-SCAN button on the remote
controller. “PRESET SCAN” appears on the
display and then the preset station with the
lowest preset number is recalled fi rst.
4. Preset stations are recalled in sequence (No.1
→ No.2 → etc.) for about 5-10 seconds each.
The time changes by the received condition. No
stored preset number will be skipped.
5. Pressing the cursor 2 button during prescanning
speeds up scanning.
Also, pressing the cursor 1 button returns to
the previous preset station.
When the desired preset station is received,
cancel the preset scan operation by press the
P-SCAN button.
CLEARING STORED PRESET STATIONS
You can remove preset stations from the memory
using the following procedure.
TOP TOP
ZONE ZONE SPEAKER SPEAKER
DISPLAY DISPLAY INPUT INPUT 7.1CH 7.1CH DIRECT PURE
PHONES
THX THX M-DAX M-DAX
MODE SURROUND CLEAR CLEAR MEMORY MEMORY T-MODE T-MODE BAND BAND EXIT EXIT MENU MENU ZONE ZONE
DOWN DOWN
VOLUME VOLUME
UP UP
INPUT SELECTOR
AUTO
SETUP MIC SETUP MIC
HDMI HDMI
DAX M-DAX
DIRECT PURE DIRECT
POWER ON/OFF
STANDBY
AV PRE TUNER AV8003 AV PRE TUNER AV8003
ENTER ENTER
3. 2.
2. 2.
3.
1. Recall the preset number to be cleared with
the method described in ”PRESET SEARCH
MODE”.
2. Press the MEMORY button on the front panel
or remote controller.
3. The stored preset number blinks in the display
for 5 seconds. WhiIe blinking, Press the CLEAR
button on the front panel or the remote.
4. “xx CLEAR” appears on the dispIay to indicate
that the specified preset number has been
cleared.
Note:
• To clear all stored preset stations, press and hold the
CLEAR and the ENTER buttons for two seconds.
• There are 50 preset channels prepared at the factory
default. The 50 channels are all set to “CHANNEL
001”. Each channel can be stored in the preset
memory. You can search for only the preset
channels.
NEURAL SURROUND MODE
When the XM Satellite Radio broadcast received
supports XM HD Surround Sound, Surround playback
is possible in Neural Surround mode.
3. 3.
2. 2.
1. Switch the remote controller to TUNER mode.
2. Press the < / > button until 001 is displayed.
3. Press the NEURAL button to tune in the Neural
surround mode.
Note:
For information on Neural Surround, see page 44.
AV8003_U_Eng.indb 59 AV8003_U_Eng.indb 59 08.4.28 10:40:31 AM 08.4.28 10:40:31 AM