Denon DCM-370 - Manual (Page 9)

9
ENGLISH
CONNECTIONS
(1) Connecting the Output Terminal
• Connect one end of the connection cord supplied with the CD Player to
the output terminals, left (L) and right (R) of the CD Player, and the other
end to the CD, AUX or TAPE PLAY input terminals, left (L) and right (R), of
the amplifier.
(3) SYNCHRO Jack Connections
• Connect the SYNCHRO jack with a DENON cassette deck which is
equipped with a SYNCHRO jack, then make a synchronized recording. Use
the connection cord supplied with the cassette deck.
• To make use of this function, also connect the output jacks and make the
settings so that a recording can be made from the CD player to the
cassette deck.
COAXIAL
DIGITAL OUT
LINE OUT
VARIABLE
CONTROL
OUT IN
SYNCHRO
AC OUTLET
PHONO CD TUNER AUX TAPE-1 /DAT TAPE-2 /MD TAPE-1 /DAT TAPE-2 /MD
L
R
PB REC
SIGNAL GND
INPUTS
L
R
R L
SPEAKER SYSTEMS
A
B
(Amplifier) Power supply outlet
DCM-370/270
OPEN/CLOSE DISC SKIP
5 DISC AUTOMATIC DISC LOADING SYSTEM
STOP PAUSE PLAY PROG
PHONES
REPEAT DCM-370 PCM AUDIO TECHNOLOGY / CD AUTO CHANGER REMOTE
SENSOR
HDCD
£ ¢ ON OFF
TRACK 1
5 2 3 4
6 7 8
9 101112 13141516
DISC MIN SEC ¤ ‚⁄ ‚‹ fi‚
1
2
3
4
5
( 1 PLAY )
NORMAL PLAY
Follow the steps below to get an understanding of the disc play
procedure.
1. Turn the power switch on and press the open/close ( 5 OPEN/CLOSE)
button to open the drawer.
2. Set the disc to be played in the front side tray.
3. Press the play button (
1 ).
4. The drawer closes and the disc just loaded is played.
5. The disc number, track number and elapsed time, etc., for the disc
currently playing appear on the display window.
6. If the open/close ( 5 OPEN/CLOSE) button is pressed while a disc is
playing, playback continues, but the drawer opens and four discs can be
replaced. The disc that can be replaced switches when the DISC SKIP
button is pressed.
Press the open/close (
5 OPEN/CLOSE) button again to close the drawer.
(1) Starting Playback
(2) Stopping Playback
OPEN/CLOSE DISC SKIP
5 DISC AUTOMATIC DISC LOADING SYSTEM
STOP PAUSE PLAY PROG
PHONES
REPEAT DCM-370 PCM AUDIO TECHNOLOGY / CD AUTO CHANGER REMOTE
SENSOR
HDCD
£ ¢ ON OFF
TRACK 1
5 2 3 4
6 7 8
9 101112 13141516
DISC MIN SEC ¤ ‚⁄ ‚‹ fi‚
1
2
3
4
5
( 2 STOP )
1. Press the stop button ( 2 STOP) to stop playback.
2. To replace discs, press the open/close ( 5 OPEN/CLOSE) button.
The disc which was playing switches over to the front side and the drawer
opens.
OPEN/CLOSE DISC SKIP
STOP PAUSE PLAY PROG
PHONES
REPEAT
5 DISC AUTOMATIC DISC LOADING SYSTEM
DCM-370 PCM AUDIO TECHNOLOGY / CD AUTO CHANGER REMOTE
SENSOR
HDCD
£ ¢ ON OFF
TRACK 1
5 2 3 4
6 7 8
9 101112 13141516
DISC MIN SEC ¤ ‚⁄ ‚‹ fi‚
1
2
3
4
5
• Set the disc you want to
played in the front side.
COAXIAL
DIGITAL OUT
LINE OUT
VARIABLE
CONTROL
OUT IN
SYNCHRO
(Cassette Deck) Power supply outlet
DCM-370/270
(2) Connecting the Digital Output Jack (COAXIAL) (DCM-370 only)
• Use a 75 Ω /ohm pin cord to connect the digital output jack (COAXIAL) of
the DCM-370 to the digital input jack (COAXIAL) on a digital processor or
MD recorder, available in stores.
COAXIAL
DIGITAL OUT LINE OUT
VARIABLE CONTROL
OUT IN
SYNCHRO
DIGITAL INPUT
COAXIAL
OPTICAL
Power supply outlet
DCM-370/270
Digital processor or MD recorder