Kleenmaid KED420 From Serial No. 706411 User Manual

Import ant user informa tion, Reversing the door opening, Instructions for use

–

This tumble dr

yer is intended f

or NORMAL DOMESTIC

USE ONL Y.

–

Please note it is not recommended that the dry

er be

placed directly next to o

vens or cook

ers, as the

perfor

mance of the dry

er may be aff

ected.

–

Any

electr

ical wor

k required to install the appliance

should be carried out b

y a qualified person.

–

It is important to clean the lint filter after each dr

ying cycle

and the condenser ever

y three or four months or the

restrictions to airflo

w will extend dr

ying times and could

cause the safety cut-out to tr

ip.

–

A car

pet must not obstr

uct the ventilation openings in the

base of the dry

er.

–

Do not stack the tumb

le dry

er on top of any other

appliances without the correct stacking kit.

–

Under no circumstances should anything other than the

recommended articles be placed in the tumb

le dry

er.

–

The tumble dr

yer should be ser

viced by an appointed

service organisation and only gen

uine parts used.

–

It is dangerous to alter or modify the product in any w

other than fitting authorised accessor

ies.

–

We recommend that the appliance is unplugged each

time after use.

It should alwa

ys be disconnected from the

electricity supply if it is to be left unattended f

or long

periods (i.e

eekends

, holidays etc.)

–

The rear of the dry

er gets quite hot during use

osition

the dry

er so that the back is not accessib

le while in

operation, b

ut the sides have a space a

vailab

le to allow

air flow

–

It is impor

tant to clean fluff from the window of the dr

yer

and around the door seal after each drying cycle

ailure

to do so could result in water leaking.

–

DO NOT

use a two-w

ay adaptor

, or extension lead.

The

dry

er must be connected to its o

wn socket.

–

DO NOT

bloc

k the air inlets at the front and back of y

our

dry

er.

–

DO NOT

allow fluff to accum

ulate around the tumble

dry

er.

–

DO NOT

exceed the recommended maxim

um load.

–

DO NOT

allow children to tamper with the controls and

keep them a

y from the dry

er when it is in operation.

–

DO NOT

place articles in the dr

yer if an

ything other than

a water solution has been used in the cleaning process

–

DO NOT

attempt to dry dr

ipping wet ar

ticles or items

containing foam r

ubber or r

ubber-lik

e materials

–

DO NOT

use the tumble dr

yer if y

ou suspect that it is

damaged in any w

ay.

Under no circumstances should you

attempt to repair the appliance yourself

.Repairs carr

ied

out by ine

xperienced persons ma

y cause serious injur

y .

Consult your local appointed ser

vice engineer and insist

on genuine spare par

ts.

THIS APPLIANCE MUST BE EARTHED

IMPORT

ANT USER INFORMA TION

These notes are provided in the interest of saf

ety .Y

ou must read them bef

ore installing or using the appliance.

REVERSING THE DOOR OPENING

MII CONDENSER

FPL ‘98

4213 094 87802

Dryers fitted with hinge cover:-

Dryers fitted without hinge cover:-

Your dryer is supplied with a reversible door. To change the direction of opening proceed as follows for your type of door.

Open the door. Undo screw
(A) remove switch strike (B)
and replace screw. Undo
screw (J) and remove buffer.
Remove screws (C) and latch
plate (D). Remove hinge cover
screw (E). Close the door.

Pull the hinge cover (F)
forwards to remove it.
Remove two outer screws
(G). Remove door. Fit latch
plate (D) with screws (C).

Reverse door and fit to dryer
in closed position.

Refit

screws (G) and hinge cover
(F). Open the door.

Fit screw (E) to secure hinge
cover. Remove screw (H) at
top of door and refit switch
strike (B) as shown. Refit
buffer (J).

Open the door. Undo screw (A)
remove switch strike (B) and replace
screw. Undo screw (J) and remove
buffer. Remove screws (C) and latch
plate (D). Remove hinge block screws
(E). Remove door from hinge blocks.

Remove hinge screws
(F) and hinge (G) and
refit to opposite side as
shown.

Refit latch plate (D) with screws (C). Remove screw (H) at top of
door and refit switch strike (B) as shown. Refit buffer (J). Fit door
to hinge blocks and secure with screws (E).

KED420 from
serial 706411

INSTRUCTIONS FOR USE

IMPORTANT:
PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE USING THIS APPLIANCE.
KEEP THEM IN A SAFE PLACE FOR FUTURE REFERENCE.

THE CONDENSER

The condenser and ducting should be cleaned 3 or 4 times a year

or more frequently if the dry

er is in constant use.

See “CLEANING

THE CONDENSER”opposite

NOTE:

The condenser will discolour through use.

REMOVING THE

CONDENSER

–

Firmly pull the condenser out.

RE-INSTALLING THE

CONDENSER

–

Carefully push the condenser back into the machine

, until it is

pushed fully home and a “clic

k”is heard.

–

Ensure all lint and fluff is removed from around the g

rille seal

before closing or w

ater may leak.

–

IMPORTANT

:The dr

yer ma

y leak if the condenser is not

correctly re-installed.

CLEANING THE CONDENSER

CAUTION:

For maxim

um efficiency , the plates are made from

very

thin aluminium and are easily damaged.

Do not try to pok

anything betw

een the plates or use a hard object or tool for

cleaning.At all times

, handle the condenser carefully and avoid

crushing the plates

–

Remove the condenser (see opposite).

–

Flush the fluff from between the plates under r

unning water

and carefully shake off e

xcess water

–

Whilst the condenser is

removed, clean as m

uch fluff

as possible from inside the

ducting by reaching a hand

into the machine.

In particular

keep the passage from the f

clear (on the right hand side of

the condenser duct).

–

After cleaning, re-install the condenser (see opposite).