InSinkErator Invite H-Contour-SS - Manual (Page 5)

select a spot under the sink to mount
tank vertically within reach of both
plumbing and electrical connections.
the tank should be within 16" or less
of faucet water lines and within 30"
or less of a standard grounded outlet.
while holding tank in place on
the spot selected for installation,
use a pencil to mark locations for
2 hanging screws.
Property Damage: Tank must be located
within 16" of faucet and within 30" or less
of a standard grounded outlet. DO NOT extend
plumbing or electrical lines.
3
without depressing the gray button,
place the snap-connect fitting at
the end of the blue 1/4" tube onto
the left fitting on the tank, pushing
until it clicks into place. (1)
slip the flexible white 7/16" tube
over barbed middle fitting and slide
down approximately 1/2". (2)
slip the clear 5/16" tube over the
far right smooth fitting and slide
down approximately 1/2". (3)
Visually check for pinched or
crimped tubes.
4
Property Damage: Pinched or blocked water
lines may cause damage to the dispenser tank.
Check to make sure tubes are connected
properly and are pushed down as far as possible.
Tank must be
mounted level
to ensure
proper operation.
Hose clamps are not needed for any
of the connections.
Mount tank vertically in an area that
allows clearance on the underside of
the tank for drainage, if necessary.
DO NOT over tighten screws.
Pre-drill 1/8" pilot holes at marks.
turn screws into pre-drilled holes,
leaving 1/4" exposed.
hang the tank on the screws.
tighten the screws with only 1/2
turn clockwise.
Screws provided are for use in wood
studs or cabinets only. Use wall anchors
(not supplied) for installation into drywall.
leave 1/4" for
hanging tank.
Brass Nut
Ferrule
Brass Insert
Wing Nut
Fiber
Washer
Brass Nut
Ferrule
Wing Nut
Fiber
Washer
1 2
3
Plastic
tube
Brass Nut
Ferrule
Brass Insert
Wing Nut
Fiber
Washer
Brass Nut
Ferrule
Wing Nut
Fiber
Washer
1 2
3
Plastic
tube
Brass Nut
Ferrule
Brass Insert
Wing Nut
Fiber
Washer
Brass Nut
Ferrule
Wing Nut
Fiber
Washer
1 2
3
Plastic
tube
(1) (2) (3)
MOUntIng the tanK
cOnnectIng faUcet tO tanK
a
a
b
NOTICE
NOTICE
9 8
Scalding Hazard: The faucet dispenses
near-boiling (212ºF) water which can
instantly cause scalds or burns. Use care
when operating this appliance.
Property Damage: Join remaining tube
to cold water supply only.
Property Damage: Join remaining tube
to cold water supply only.
turn on the cold water supply.
Depress the dispenser’s HOT
handle and hold it until water flows from
the spout (approximately 1 to
2 minutes).
Run the water for at least 2 minutes to
flush lines (both the hot and cold handles
independently if applicable).
6
check all connections to ensure they are
tight and that there are no leaks.
Plug in instant hot water tank.
Water will be cold at first.
Allow 12-15 minutes for water to reach
target temperature.
Gurgling or hissing is normal during the
initial heating cycle.
5
Install a t-fitting (not included) onto the
cold water supply line.
Install dedicated water control valve with
3/8" compression fitting.
at the end of the white 3/8" tube from
the quick-connector, slide the supplied
brass nut and ferrule over the tube and
then push in the brass tube insert.
Insert the white 3/8" tube into the 3/8"
compression fitting and tighten.
HC-View/HC-Wave
Install a t-fitting (not included) onto the
cold water supply line.
Install dedicated water control valve with
1/4" compression fitting (not included).
at the end of the copper 1/4" tube,
slide the brass nut and ferrule provided
with the control valve over the tube.
Insert the copper tube into the 1/4"
compression fitting and tighten.
H-View/H -Wave/Contour/Classic
Electric Shock Hazard: A standard grounded
outlet within 30" of the dispenser is required
under the sink. Do not use an extension
cord set with the dispenser.
Brass Nut
Ferrule
Brass Insert
Wing Nut
Fiber
Washer
Brass Nut
Ferrule
Wing Nut
Fiber
Washer
1 2
3
Plastic
tube
fInal wateR cOnnectIOn
fIll tanK & then cOnnect POweR
b
a
a
a
NOTICE
NOTICE
NOTICE
NOTICE
3/8"
Plastic
tube
Brass
nut Brass
Insert
ferrule
1/4"
copper
tube
Brass
nut
ferrule
Brass Nut
Ferrule
Brass Insert
Wing Nut
Fiber
Washer
Brass Nut
Ferrule
Wing Nut
Fiber
Washer
1 2
3
Plastic
tube
To see a tutorial of this installation:
http://goo.gl/AZOHu