Heat sink component replacement -26, Dc-340, Powermax1650 – Hypertherm Powermax1650 Service Manual User Manual
Page 53
MAINTENANCE
3-26
powermax1650
Service Manual
2
Heat Sink Component Replacement
Installation
• Install components to the heat sink as shown below.
• Use new thermal pads on temperature sensor.
• Use white thermal grease (Part no. 330002) on all components except for IGBT, PFC (Part no. 128745). Use
grey thermal grease (Part no. 128836) on IGBT, PFC, see Note 3. Apply a thin coat to the component, install with
screws, and tighten to required torque. Note: Remix grease if material seperates.
• Re-torque after 2 minutes. Repeat until torque is maintained. Clean excess grease from heat sink.
Notes:
1
Apply white thermal grease DC-340 (Part no. 027662) and torque to 8 in-lb (9 kg cm.)
2
Apply white thermal grease DC-340 (Part no. 027662) and torque to 35 in-lb (40 kg cm).
3
Apply grey thermal grease TC-330 (Part no. 128836) and torque to 35 in-lb (40 kg cm).
Note: grey thremal grease TC-330 is included with PFC IGBT Replacement Kit (Part no. 128745)
Thermal Pad
Thermal Grease
DC-340
PMX600.28
ቢ
ባ
ባ
ባ
ባ
ቢ
ቢ
ቢ
ቤ
- 80669J Rev.3 (304 pages)
- EDGE Pro Ti Shape Cutting Control Rev.2 (288 pages)
- HD3070 Plasma Arc Cutting System w/ Manual Gas Console (281 pages)
- MAXPRO200 Rev.2 (294 pages)
- MicroEDGE Pro Shape Cutting Control Rev.2 (182 pages)
- HPR260 Auto Gas Preventive Maintenance Program Rev.4 (288 pages)
- Powermax1650 (317 pages)
- Shape Cutting Control (66 pages)
- PHC Sensor (58 pages)
- HTA Rev 6.00 Operators Manual (212 pages)
- HTA Rev 7.00 Install Guide (242 pages)
- THC Control Board Replacement (13 pages)
- THC Plasma Interfacer Upgrade (9 pages)
- THC X-Y Table Product Configuration (20 pages)
- D845GERG2 (128 pages)
- MRT2 (64 pages)
- MRT (98 pages)
- Duramax Hyamp Long Handheld Torches (92 pages)
- Duramax Hyamp Robotic Torch (74 pages)
- HyIntensity Fiber Laser Rev.3 (240 pages)
- PCBS-0124 (70 pages)
- SuperMicro 370SBA 533Mhz (90 pages)
- LR2075 (56 pages)
- Phoenix 8.0 (585 pages)
- LH2125 (60 pages)
- HD3070 w/ Automatic Gas (35 pages)
- HD3070 w/Manual Gas (43 pages)
- HD4070 Rev.8 (278 pages)
- HD4070 Product Configuration (88 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (32 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (33 pages)
- HPR800XD Manual Gas Rev.2 (368 pages)
- HPRXD Short Torch with Integrated Lead Rev.1 (30 pages)
- HT4001 (59 pages)
- DuraChill 5 HP Air-Cooled Chiller For Hypertherm (29 pages)
- HT4001 Air Injected Water Muffler System (40 pages)
- H601 Power Supplies (62 pages)
- MAX200 Remote Switch (9 pages)
- HT4100 Plasma Arc Cutting System Operating (50 pages)
- HT4001 Plasma Arc Cutting System (259 pages)
- HSD130 HySpeed Plasma (233 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.7 (53 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.27 (289 pages)
- MAX200 Water Muffler (39 pages)
- HT2000LHF Product Configuration (23 pages)