Flowserve 132000 Series - Manual (Page 12)

12
Flow Control Division
Kammer Control Valves
Fault Possible Cause Remedy
Stem motion 1. Packing excessively tightened 1. Tighten gland nut (see table 1)
impeded 2. Operating temperature too 2. Note operating data and contact dealer
high for selected trim
3. Supply pressure inadiquate
3. Check system for leaks in the supply pressure or signal lines. Re-
tighten the connections, if necessary replace leaky lines
4. Positioner defective 4. See operating instructions for positioner
Excessive 1. Bonnet loose 1. See step 21.7 for correct tightening of bonnet.
leakage 2. Worn or damaged 2. Re-machine or replace seat ring/plug.
seat ring/plug
3. Gaskets damaged
3. Replace gaskets
4. Inadiquate actuator thrust 4. Check air feed. If air feed is OK, contact dealer.
5. Plug incorrectly adjusted 5. Correctly adjust plug according to step 18.3
6. Incorrect direction of flow 6. Check specification. Contact dealer
7. Handwheel incorrectly 7. Adjust handwheel
adjusted (acts like end stop)
Inadiquate flow 1. Plug incorrectly adjusted 1. Correctly adjust plug according to step 18.3
(short stroke)
2. Positioner defective
2. See operating instructions for positioner
3. Operating requirements 3. Check operating data. Contact dealer
too high
Plug slams 1. Plug adjustment incorrect 1. Correctly adjust plug according to step 18.3
2. Inadiquate supply pressure 2. Check supply pressure, seal leaks, remove blockage
3. Trim too large for 3. Replace trim
flow rate
22 Trouble-shooting chart
All data subject to change without notice
©09.2003 Flowserve Corporation. Flowserve and Kämmer are trademarks of Flowserve Corporation
Regional Headquarters
Flowserve EMA Flowserve America Flowserve Asia
Burrell Road, Hayward Heath 1350 N. Mt. Springs Prkwy. 12 Tuas Avenue 20
West Sussex, RH16 1TL Springville, UT 84663 638824
England USA Republic of Singapore
Telephone: +44 (0) 1444 314400 Telephone: +1 801 489 8611 Telephone: +65 862 3332
Facsimile: +44 (0) 144 3144401 Facsimile: +1 801 489 3719 Facsimile: +65 862 4940
Main Sales Offices EMA (Europe, Middle East, Africa)
Flowserve France Flowserve UK Flowserve Switzerland Flowserve Germany
7 Avenue de la Libération Station Road Allee du Quartz 1 Manderscheidtstr. 19
63300 Thiers Cedex Pershore, Worcestershire CH-2300 La-Chaux-de Fonds 45141 Essen
France England WR102BZ Switzerland Germany
Telephone: +33 (0) 4 73 80 42 66 Telephone: +44 (0) 1386 55 45 51 Telephone: +41 (0) 32 925 9700 Telephone: +49 (0) 201 8919 5
Facsimile: +33 (0) 4 73 80 14 24 Facsimile: +44 (0) 1386 55 49 68 Facsimile: +41 (0) 32 926 5422 Facsimile: +49 (0) 201 8919 662
Flowserve South Africa Flowserve Middle-East Flowserve Austria Flowserve Benelux
Units 1 and 2 C/O Saleh & Abdulaziz Abahsain Kasernengasse 6 Van Leeuwenhoekweg 6
26, Imvuba Road, Sebenza Ext 6 P.O. Box 209
Edenvale, Gauteng
Edenglen 1613
Al Khobar 31952 9500 Villach 3225 LX Hellevoetsluis
South Africa Saudi Arabia Austria The Netherlands
Telephone: +27 11 609 2094 Telephone: 9663 857 3442 Telephone: +43 (0) 424241 181-0 Telephone: +31 (0) 181 330044
Facsimile: +27 11 609 3735 Facsimile: 9663 859 5284 Facsimile: +43 (0) 424241 181 50/51 Facsimile: +31 (0) 181 330040
Flowserve Italy Flowserve Spain Flowserve Portugal Flowserve Scandinavia
Via Prealpi, 30 Luis Cabrera, 86-88 Av. Dr. Antunes Guimaraes, 1159 Gelbgjutaregatan
Cormano (Milano) E-28002 Madrid Porto 4100-082 58933 Linköping, Östergötland
Italy Spain Portugal Sweden
Telephone: +39 (0) 2663251 Telephone: +34 9 15 152 032 Telephone: +351 22 619 8770 Telephone: +46 13 316100
Facsimile: +39 (0) 26151863 Facsimile: +34 9 14 136 747 Facsimile: +351 22 619 7575 Facsimile: +46 13 136054
Flowserve Eastern Europe
12, av. du Québec
91965, Courtaboeuf Cedex
France
Telephone: +33 (0) 1 60 923 251
Facsimile: +33 (0) 1 60 923 299