Caple TDF200 - Manual (Page 7)

• DRYING PROGRAMS
• PRESENTATION OF THE CONTROL PANEL
13 12
EN EN 5 / PROGRAMMING
• Adding or removing an item during
drying :
— Press “Start/Pause” to interrupt drying
and open the door.
— Insert or remove the item or items and close
the door.
— Press the “Start/Pause” button
to resume
drying.
Advice :
To ensure the effectiveness of the
Steam programs, you are discouraged from
interrupting these programs mid-cycle.
• Altering programming or drying
during operation :
If you have entered the wrong program, you
can change your selection during the cycle.
— Press “Start/Pause”
to interrupt drying.
— Select another program using the program
dial.
— Press the “Start/Pause” button
to
resume drying.
• Cooling cycle :
All programs finish with a cooling cycle that
lasts for a few minutes to allow the washing to
cool gradually.
Important :
Do not stop your dryer before this cycle
has finished.
• End of program and appliance
stop :
At the end of program, the display shows
“0:00”. The “Filter” and “Tank Full” lights flash
alternately to remind you that you must clean
the filter and empty the water collection tank
after every drying cycle:
— Press the “On/Off” button
.
— Empty your dryer.
— Clean the filter and empty the water collec-
tion tank (see the “REGULAR MAINTE-
NANCE” section).
H H
G G
G G
G G
G G
Advice :
Consult the Programs table on the next page to determine the program needed for the type
of items.
5 / PROGRAMMING
Programs dial
Tumbling
Buzzer
Additional drying
Delayed start “-”
Delayed start “+”
Start/Pause
On/Off
H H
G G
F F
E E
D D
C C
B B
A A
Your appliance has two functions :
- a drying function that includes 8 programs
- a steam treatment function that includes 3 programs
Your appliance is equipped with an automatic dryness detection system. The appliance will stop
when the chosen level of dryness has been achieved (see the program chart on the following
pages).
• Starting the appliance :
Check that the power cable is plugged in. The appliance will not start unless the door is properly
closed.
— Press the “On/Off” button
.
— Select your program (see the table “Your dryer’s programs” on the following pages) by turning
the Programs dial (it turns in both directions). The indicator light shows you the program you have
selected.
— Press “Start/Pause”
and the program will start. (The “In use” indicator lights up).
• Time remaining :
The time displayed at the start of a cycle corresponds to a full load. It is provided for informatio-
nal purposes. The actual time adjusts during the cycle based on the load of laundry.
When the cycle begins, the "Time remaining" symbol
flashes. This symbol turns to a steady
light when the remaining time has been calculated.
Pause Stop Pause Stop Pause Stop
Pause Stop
Pause Stop
Pause Stop
Pause Stop Pause Stop
Pause Stop Pause Stop
Pause Stop
Pause Stop
Pause Stop
G G
H H
Pause - Drying - Cooling down - End of program
Program progress :
Time remaining Delayed Start
Additional Drying Buzzer Anti-crease
Filter
Tank Full
Steam Tank +
Program stop
Time remaining
End of program
The “Filter” and “Tank Full” lights flash
Cooling cycle
8 Kg
STEAM POWER
Start / Pause On / Off
Delayed Start
Additional Drying Buzzer Anti-crease STEAM
Filter
Tank Full
Steam Tank
Cotton
Cotton Extra Dry
Dry
Iron Dry
Iron Dry
Mixed Mixed
Synthetics
Dry
Delicates
Air Woollens
Pause Stop
TDF200
+
A A B B C C D D E E G G H H F F
Pause Stop
Delayed Start
Additional Drying Buzzer Anti-crease
Filter
Tank Full
Steam Tank +
Delayed Start
Additional Drying Buzzer Anti-crease
Filter
Tank Full
Steam Tank +
Delayed Start
Additional Drying Buzzer Anti-crease
Filter
Tank Full
Steam Tank +