Caple Di605DL - Manual (Page 7)

.6.
Starting the Appliance GB
Starting a wash cycle
After having completed all of the installation steps in the preced-
ing paragraphs, turn on the water to the unit, partially open the
door of the dishwasher, and press the power button "B" located
on the control panel. The "A" indicator light will come on. At this
point, the appliance is on and ready to be programmed.
Setting and Starting a wash Cycle
Choose the desired cycle by pressing the cycle selection button
"H". Each time it is pressed, one of the cycle indicator lights "G"
will come on in succession. At that time, the display "I" will show
number of hours for the programme.
Choose the wash cycle you feel is most appropriate for the type
of dishes that need washing (consult the wash cycle table con-
tained in this manual, especially when first using the appliance).
Close the door and after a few seconds, a short acoustic signal
will sound indicating that the wash cycle has begun and cannot
be modified. If necessary, read the paragraph entitled, "Cancel-
ling or modifying a cycle while underway". The end of the cycle
will be signalled by a double acoustic sound, and the indicator
light "G" will begin to blink.
Cancelling or modifying a cycle while underway...
Premise: A cycle that is underway can only be modified if it has
only been running for a short time.
Otherwise, the detergent may have already been used, and the
appliance may have already drained the wash water. If this is the
case, the detergent dispenser must be refilled (see the paragraph
entitled, "Loading the Detergent").
To change the cycle currently underway, open the door, press
the power botton "B", then all the settings will be cancelled. Once
the cycle has been cancelled, the dishwasher will emit a short
acoustic sound and the relative indicator light will turn off.
To set a new wash cycle, follow the instructions contained in the
paragraph entitled, "Setting and Starting a Wash Cycle".
If you forget to load some of the dishes...
The wash cycle can be interrupted by opening the door carefully
(in order to avoid being sprayed by hot water). When the door is
closed again, the cycle will automatically restart at the point where
it left off.
At the end of the wash cycle...
The end of the cycle will be indicated by a double acoustical
signal and the blinking of the "G" indicator light. And the number
on the display "I" will turn "0". Open the door, turn off the appli-
ance using the power botton and turn off the water supply to the
unit. Wait a few minutes before removing the dishes so as to
avoid handling them while still hot (when they are more suscep-
tible to breakage) and to get better drying results.
Setting The Start Delay Time
Open the door of the dishwasher partially. If the "D" button is
pressed (see, Close-up View "Control Panel"). The start time of
the wash cycle can be delayed for between 1 to 12 hours.
Each time the button is pressed, the display "I" will show the
number of hours for the delay period.
After selecting the delay time, the wash cycle can be set, as
explained in "Starting a wash cycle..." There will be a short acous-
tic signal, and at this point the delay period will begin to count
down. During this period the delay indicator light "E" will blink. At
the end of the delay time, the indicator will stop blinking and the
cycle will start.
Wash Cycle Adjustment Buttons
1/2 Load Button
This button (see "Close-up View-Control Panel", letter "C") makes
it possible to wash dishes using only the upper rack if there are
not enough dishes for a full load, This will allow you to save on
water and electrical energy.
It cannot be used with the heavy duty wash cycles.
a) During the delay period, it is preferable not to change any of
the settings. If it is necessary, all of the settings must be can-
celled by pressing the power button"B" to indicate that all of the
settings have been cancelled.
At this point, all of the steps for "Setting the Wash Cycle with a
delayed Start Time" and "setting and Starting a Wash Cycle"
must be repeated, following the instructions contained in the cor-
responding sections.
b) If the door is opened during the delay period, the indicator will
blink and acoustic signal will sound, and the countdown will stop.
It will begin again when the door is closed .
NOTE: