Caple C176L - Manual

English GB
4
ENVIRONMENTAL HINTS
Packing
Do not throw the packing into the garbage: first sort out the
different materials (i.e.: steel, cardboard, polystyrene), fol-
lowing local regulations.
Conformity declaration
This appliance incorporates parts intended to come into con-
tact with foodstuffs in compliance with EEC directive
89/109/CEE.
Information
This appliance is free of CFC’s (refrigerant circuit contains R134a)
or free of HFC’s (refrigerant circuit contains R600a - Isobutane).
For more details, please refer to the rating plate on the appliance.
For appliances with Isobutane (R600a)
The refrigerant Isobutane is a natural gas of high environmen-
tal compatibility but which is inflammable. Therefore, it is es-
sential to ensure that the ducts of the refrigerant circuit do
not get damaged.
KNOW YOUR APPLIANCE
The refrigerator you have just purchased allows you to store fresh
foods. If equipped with a low temperature compartment, it al-
lows the storage of frozen foods and the production of ice cubes
as well. Please read the following instructions carefully. The inclu-
de a full description of your appliance and useful hints to enable
you to achieve the correct performances required to store foods.
DESCRIPTION OF THE APPLIANCE
(Fig. 1)
A) Thermostat (Depending on the model)
1) Light switch
2) Temperature control knob for both compartments (thermostat)
3) Low temperature compartment
4) Adjustable shelves (in height)
5) Crisper drawers
6) Inner door liner with shelves
7) Butter and eggs compartment
8) Defrosting button
INSTALLATION
This appliance is for building-in and do not install it as a free-
standing unit.
- Please ensure that your appliance is undamaged. Any tran-
sport damage must be reported to your dealer within 24
hours of receipt.
- Do not install the appliance near to heat sources such as
cookers, central heating, boilers, sunlight, etc. It must how-
ever be located in a well ventilated dry space.
- To install this appliance in a column, please follow the sepa-
rate instructions supplied.
- Make sure that the column is provided with an air inlet at
the front and an air outlet at the rear (Fig. 2).
- Leave the appliance to stand for 1 h prior to connecting it to
the mains. In the meantime clean the compartments (see
chapter "Maintenance") and fit the accessories (Fig. 3).
ELECTRICAL CONNECTION
AND OPERATION
Please check that the voltage indicated on the rating plate si-
tuated inside the compartment (Fig. 5) corresponds to the
voltage in your home (Fig. 4).
The earthing of this appliance is compulsory by law.
The manufacturer will accept no liability for injury to
person or damage to objects arising from the non-ob-
servance of this requirement.
FOR GREAT BRITAIN ONLY
ELECTRICAL INFORMATION
"WARNING - THIS APPLIANCE MUST BE EARTHED"
FUSE REPLACEMENT
If the mains lead of this appliance is fitted with a BS 1363A 13
amp fused plug, to change a fuse in this type of plug use an
A.S.T.A. approved fuse to BS 1362 type and proceed as fol-
lows:
1. Remove the fuse cover (A) and fuse (B)
2. Fit replacement 13A fuse into fuse cover
3. Refit both into plug.
IMPORTANT: The fuse cover must be refitted when chang-
ing a fuse and if the fuse cover is lost the plug must not be
used until a correct replacement is fitted. Correct replace-
ments are identified by the colour insert or the colour embos-
sed in words on the base of the plug.
Replacement fuse covers are available from your local electri-
cal store.
CONNECTION TO A REWIREABLE PLUG
If the fitted plug is not suitable for your socket outlet, then it
should be cut off and disposed of in order to avoid a possible
shock hazard should it be inserted into a 13A socket elsewhere.
A suitable alternative plug should then be fitted to the cable.
The wires in this mains lead are coloured, in accordance with
the following code:
BLUE-“NEUTRAL" ("N")
BROWN-"LIVE" ("L")
GREEN AND YELLOW - "EARTH" ("E")
1. The GREEN AND YELLOW wire must be connected to the ter-
minal in the plug which is marked with the letter "E" or by the
Earth symbol
or coloured green or green and yellow.
2. The BLUE wire must be connected to the terminal which is
marked with the letter "N" or coloured black.
3. The BROWN wire must be connected to the terminal which
is marked with the letter "L" or coloured red.
For the Republic of Ireland only
The information given in respect of Great Britain will frequen-
tly apply, but a third type of plug and socket is also used, the
2-pin, side earth type. In this case, the wire which is coloured
GREEN AND YELLOW must be connected to the EARTH con-
tact, and the other two wires to the two pins, irrespective of
colour. The supply to the socket must be fitted with a 16 amp
fuse.
Ꭾ
Ꭽ
CABLE CLAMP
YELLOW & GREEN ൴
BLUE ൽ
Connection to a
typical 13 amp plug
BROWN ൻ