Caple Oi360SS - Manual (Page 5)

9
Warning!
Before connecting the flexible exhausting pipe to the
motor, make sure the stop valve, which is on the air
outlet of the motor, can swing.
Sucking version
* Fix the pipe-bearing stirrup (Fig.10Y) to the wall or
ceiling by using the proper reinforcements and screws
in equipment. Connect the cooker-hood flange with the
evacuation hole by using a proper pipe.
(For versions
with display only) Lift the lower pipe until the cable strap
coming out of the sucking unit is uncovered and connect
it to the display cable strap. Put down the lower pipe
while paying attention it is being properly introduced
into the hood.
Perform the electrical connections. The
superior end of the pipe is to be fixed laterally to the
pipe bearing (Fig.11Y) by using the two self-threading
screws. Now mount the inferior chimney by inserting
it through the front side of the cooker hood and then
turning it down until it is fixed inside (Fig.11).
Filtering version
* In the filtering version the air deviator is fixed through
the screws supplied (Fig.12), by using the holes which
are on the back of the upper telescopic section. Connect
the flange of the appliance with the air deviator through
an appropriate pipe. Connect the appliance with the
electric mains.
(For versions with display only) Lift the
lower pipe until the cable strap coming out of the sucking
unit is uncovered and connect it to the display cable
strap. Put down the lower pipe while paying attention
it is being properly introduced into the hood.
Mod. SL TC - Touch Control version (Dis.21)
A: Light switch On/Off
B: Reduce speed
C: Luminous telltale
D: Incrase speed
E: 10 - minute timer
The touch control key allows the function desired by touching
the relative key. The luminous telltales (C) positioned at the
center of the keyboard indicate the suction speed set. In
case of an active timer, the upper telltale (C) flashes.
If the push button console malfunctions, remove the grease
filters and press the red button inside the appliance twice.
If the electrical power supply to the product SLTC is cut,
15 seconds are needed for self-diagnostics after the
functions are restored. In the meanwhile, its operation
may be incorrect.
Mod. SL … I - Intensive version (Dis.22)
A: Light switch On/Off
B: Motor switch On/Off (1st rate level)
C: 2
nd
rate level switch
D: 3
rd
rate level switch
E: Intensive speed switch
F:
10 - minute timer
Pressing the Intensive speed key “I”, suction is at
maximum speed for the duration of 4 minutes. Once 4
minutes have passed, the product returns to the previous
setting. Example: starting from 2
nd
speed and pressing
key “I” suction will go to the maximum speed for 4
minutes. Successively the hood returns to 2
nd speed.
Mod. SL Module TD - version with display (Dis.18)
A: 1
st
speed activated
B: 2
nd
speed activated
C: 3
rd
speed activated
D: 4
th
speed activated
E: Light on
F:
Set timer 10 min.
Model with remote control (Fig.17)
6 - channel radio control for cooker hood remote control.
Technical characteristics:
- Battery feeding
: 12V
- Frequency : 433,92 Mhz
- Max. Consumption : 25 mA
- Working temperature : -20 + 70
°C
- Dimensions : 45x75x14 mm.
Functioning:
The transmitter is provided with 6 buttons for the cooker
hood functioning, which are as follows:
: ON/OF light switch.
01 : ON 1 st speed level-OFF motor switch.
2 : 2 nd speed level switch.
3 : 3
rd
speed level switch.
4 : 4
th
speed level switch.
: 10 minutes timer.
WORKING
Mod. S-SE-Module - Standard version (Fig. 13)
A: Light switch on/off
B: Motor switch on/off (1st rate level)
C: 2
nd
rate level switch
D: 3
rd
rate level switch
E: Warning gem
Mod. SM (Fig. 14)
A: Light switch on/off
B: Motor switch on/off (1st rate level)
C: 2
nd rate level switch
D: 3
rd
rate level switch
E: 10-minute timer
F:
Warning gem
Mod. SL - Module - Luxury version (Fig. 15)
A: Light switch on/off
B: Motor switch on/off (1st rate level)
C: 2
nd
rate level switch
D: 3
rd
rate level switch
E: 4
th
rate level switch
F: 10-minute timer.