Campomatic C64WTI - Manual (Page 10)

-10-
-10-
CHANGING OVEN LAMP
Changing Oven Lamp
1. Pull the plug out of socket.
2. Turn the lamp fixing glass counter-
clockwise direction to seperate it.
3. To seperate lamp from body turn it to
counter-clockwise direction.
4. Fix new lamp that you gain from
authorised service in place of old lamp.
This appliance is marked according to the European directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent potential
negative consequences for the enviroment and human health, which could
otherwise be caused by inappropriate waste handling of this product.
The symbol on the product indicates that this product may not be treated as
household waste. İnstead it shall be handed over to the applicable collection point
for the recycling of electrical and electronic equipment.
Disposal must be carried out in accordance with local enviromental regulations for
waste disposal.
For more detailed information about treatment, recovery and recycling of this product, please contact
your local city office, your household waste disposal service or the shop where you purchased the
product.
Removing Oven Door for Easy Cleaning
Before cleaning oven door, we advise you to follow below steps to seperate oven
door from body :
1- Open the door completely
2- Insert the pin as in figure. Make sure that this is done on both hinges.
3- Push up the locking part of hinge with screwdriver as shown in Figure.
4- Lift the door slightly as if closing, then with both hands supporting the door, pull
it away from the oven.
Clean the glass part of oven door with hot water and only a soft cloth.
Inserting the Oven Door
After cleaning set the door to insert oven door to oven body it is recommended to
apply below steps :
1- Hold the door in an open position and push up the locking part with
screwdriver.
2- Place hinges into the hinge holes.
3- Support the oven door and push down the locking part with screwdriver.
4- Remove pins from the hinges. Open and Close the door to make sure that it
has been fitted correctly.
CHANGING OVEN LAMP
Changing Oven Lamp
1. Pull the plug out of socket.
2. Turn the lamp fixing glass counter-
clockwise direction to seperate it.
3. To seperate lamp from body turn it to
counter-clockwise direction.
4. Fix new lamp that you gain from
authorised service in place of old lamp.
This appliance is marked according to the European directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent potential
negative consequences for the enviroment and human health, which could
otherwise be caused by inappropriate waste handling of this product.
The symbol on the product indicates that this product may not be treated as
household waste. İnstead it shall be handed over to the applicable collection point
for the recycling of electrical and electronic equipment.
Disposal must be carried out in accordance with local enviromental regulations for
waste disposal.
For more detailed information about treatment, recovery and recycling of this product, please contact
your local city office, your household waste disposal service or the shop where you purchased the
product.
Removing Oven Door for Easy Cleaning
Before cleaning oven door, we advise you to follow below steps to seperate oven
door from body :
1- Open the door completely
2- Insert the pin as in figure. Make sure that this is done on both hinges.
3- Push up the locking part of hinge with screwdriver as shown in Figure.
4- Lift the door slightly as if closing, then with both hands supporting the door, pull
it away from the oven.
Clean the glass part of oven door with hot water and only a soft cloth.
Inserting the Oven Door
After cleaning set the door to insert oven door to oven body it is recommended to
apply below steps :
1- Hold the door in an open position and push up the locking part with
screwdriver.
2- Place hinges into the hinge holes.
3- Support the oven door and push down the locking part with screwdriver.
4- Remove pins from the hinges. Open and Close the door to make sure that it
has been fitted correctly.