BUG-O Systems UNI-BUG II - Manual (Page 20)

5
The UNI-BUG II can operate without a track as shown below. A gear motor
turns two drive wheels on one side of the workpiece. On the other side of the
workpiece is a bracket which has four idler wheels mounted on it. An idler
screw knob is used to move the idler wheel bracket into the workpiece and
clamp it between the four idler wheels and the two drive wheels.
BUG-1855 Welding Group is required to clamp and position a welding gun.
BUG-1875 Cutting Group is available for cutting applications.
INTRODUCTION (CONT’D.)
SET-UP
1. Loosen the idler screw knob to open the gap between the idler wheels
and the drive wheels. When the gap is large enough, drop the machine
over the workpiece edge.
2. The machine should be firmly resting on the front and back roller
supports and tilt forward in the direction of desired travel.
3. Engage the idler screw knob until all of the idler and drive wheels are
contacting the workpiece. Tighten another 1/2-3/4 turn to firmly clamp
the workpiece.
4. Adjust the UNI-BUG II racking attachment so the welding gun or cutting
torch is properly positioned. This should always be placed below the
center of the machine so that the gun or torch can hold the same relative
position as the machine moves from a straight to a curved work section.
5. Set the machine speed using the speed control.
6. Set the travel switch to “ON”.
7. The Uni-bug II comes with a power cord only and the amphenol for
connecting the contactor to the machine.
Weld Contact - There are two contact cables available: UNI-1085-25 or
UNI-1085-50 (sold separately). The other option is to build your own using
a heavy lamp type cord and wire it into the 4-pin amphenol. You only need
two wires as you connect pin A & B then C & D together to make it work.
8. Turn on the weld contactor switch to begin welding.
FEATURES
Support roller
Idler screw knob
(to engage idler
wheels)
Front motor drive wheel
to move UNI-BUG II
Front idler wheel
Bracket that holds
idler wheels
20
WARRANTY
LIMITED 3-YEAR
WARRANTY
MODEL ____________________________
SERIAL NO. ________________________
DATE PURCHASED: _________________
WHERE PURCHASED: _______________
For a period ending one (1) year from the date of invoice, Manufacturer warrants
that any new machine or part is free from defects in materials and workmanship and
Manufacturer agrees to repair or replace at its option, any defective part or machine.
HOWEVER, if the invoiced customer registers the Product Warranty by returning the
Warranty Registration Card supplied with the product within 90 days of the invoice
date, or by registering on-line at www.bugo.com, Manufacturer will extend the war-
ranty period an additional two (2) years which will provide three (3) total years from
the date of original invoice to customer. This warranty does not apply to machines
which, after Manufacture’s inspection are determined by Manufacturer to have been
damaged due to neglect, abuse, overloading, accident or improper usage. All ship-
ping and handling charges will be paid by the customer.
The foregoing express warranty is exclusive and Manufacturer makes no represen-
tation or warranty (either express or implied) other than as set forth expressly in
the preceding sentence. Specifically, Manufacturer makes no express or implied
warranty of merchantability or fitness for any particular purpose with respect to any
goods. Manufacturer shall not be subject to any other obligations or liabilities what-
soever with respect to machines or parts furnished by Manufacturer.
Manufacturer shall not in any event be liable to Distributor or any customer for any
loss of profits, incidental or consequential damages or special damages of any kind.
Distributor’s or customer’s sole and exclusive remedy against Manufacturer for any
breach of warranty, negligence, strict liability or any other claim relating to goods de-
livered pursuant hereto shall be for repair or replacement (at Manufacturer’s option)
of the machines or parts affected by such breach.
Distributor’s Warranty:
In no event shall Manufacturer be liable to Distributor or to any customer thereof for
any warranties, representations or promises, express or implied, extended by Dis-
tributor without the advance written consent of Manufacturer, including but not limited
to any and all warranties of merchantability or fitness for a particular purpose and
all warranties, representations or promises which exceed or are different from the
express limited warranty set forth above. Distributor agrees to indemnify and hold
Manufacturer harmless from any claim by a customer based upon any express or
implied warranty by Distributor which exceeds or differs from Manufacturer’s express
limited warranty set forth above.
HOW TO OBTAIN SERVICE:
IF YOU THINK THIS MACHINE IS NOT OPERATING PROPERLY, RE-READ THE
INSTRUCTION MANUAL CAREFULLY, THEN CALL YOUR AUTHORIZED BUG-O
DEALER/DISTRIBUTOR. IF THEY CANNOT GIVE YOU THE NECESSARY SERVICE,
WRITE OR PHONE US TO TELL US EXACTLY WHAT DIFFICULTY YOU HAVE
EXPERIENCED. BE SURE TO MENTION THE MODEL AND SERIAL NUMBERS.