Televes T.0X DVBS2-COFDM CI TWIN MUX 3TP(2SAT):2CH - Manual (Page 6)

MUX DVBS2 - QAM/COFDM CI Twin
6
Important safety instructions
General installation conditions
• Before handling or connecting the equipment, please read this
manual.
• In order to reduce the risk of fire or electric shock, do not expose the
equipment to rain or moisture.
• Do not take the cover off the equipment without disconnecting it
from the mains.
• Do not obstruct the equipment’s ventilation system.
• Please allow air circulation around the equipment.
• The equipment must not come into contact with water or even be
splashed by liquids. Do not place containers with water on or near the
equipment if it is not adequately protected.
• Do not place the equipment near sources of heat or in excessively
moisture conditions.
• Do not place the equipment where it may be affected by strong
vibrations or knocks.
• This symbol indicates that the equipment complies with
the requirements of CE mark.
Inputs/Outputs/Connections description
The unit (Fig. 1) is provided with:
1. IF satellite input
2. IF satellite input/output
3. RF input
4. RF output
5. Module power supply input
6. Status LED
7. Control BUS connector
8. Slot CAM
9. Programmer / PC connector
Introduction
The multiplexer can demodulate up to three DVBS or DVBS2 signals from one
or two satellite IF inputs.
The user selects which services will be transmodulated in each of the
two available outputs. Two transport stream are created, which are then
modulated in QAM (564401) or COFDM (564301) format and converted to
their respective output channels using an agile up-converter.
A Common Interface slot is available. A conditional access module (CAM) can
be inserted to descramble output services.
To configure the multiplexer operating parameters (input frequency, output
channel, modulation format and adaptation of services) the universal
programming unit (ref. 7234) or the TSuite software can be used.
Technical specifications
Satellite
demodulator
Input frequency MHz 950 - 2150 Through losses (typ.) dB < 1.5
Symbol rate Mbaud 2 - 45 Modulation
DVB-S2 QPSK, 8PSK
DVB-S QPSK
Frequency steps MHz 1 FEC inner code LDPC 9/10, 8/9, 5/6, 4/5, 3/4, 2/3, 3/5, 1/2
IN/OUT connectors tipo “F” female FEC outer code Bose-Chaudhuri-Hocquenghem
Input impedance ohm 75 Roll-off factor % 20, 25, 35
LNB powering Vdc/KHz 13-17- OFF / 22KHz (ON-OFF) Return losses (min.) dB 10
Satellite selection (DiSEqC) Port A, B, C, D
QAM modulator
(Ref. 564401)
Modulation format QAM 16, 32, 64, 128, 256 Scrambling DVB ET300429
Symbol rate Mbaud 1 - 7.2 (select.) Interleaving DVB ET300429
Roll-off factor % 15 Bandwidth (max.) MHz 8.3
Block code Reed Solomon (188, 204) Spectral inversion (selectable) Normal / Inverted
OFDM
modulator
(Ref. 564301)
Modulation format QPSK, 16QAM, 64QAM Scrambling DVB ET300744
Guard interval 1/4, 1/8, 1/16, 1/32 Interleaving DVB ET300744
FEC 1/2, 2/3, 3/4, 5/6, 7/8 Cell_id Selectable
Bandwidth MHz 6, 7, 8 Spectral inversion (selectable) Normal / Inverted
RF output
Output frequency (selectable) MHz 46 - 862 Through losses (typ.) dB < 1.5
Frequency
steps
564101
KHz
250
Return losses (typ.) dB > 12
564201 166 - 125 (selectable)
Max. output level dBµV 80 ±5 IN/OUT connectors tipo “F” female
Attenuation (selectable) dB > 15 Output impedance ohm 75
General
Consumptions @ 24Vdc
(with signal)*
mA
530 (564301) 540 (564401) => (LNB not powered/ CAM not inserted)
630 (564301) 640 (564401) => (LNB not powered/ CAM inserted)
880 (564301) 890 (564401) => (one LNB powered/ CAM inserted)
1130 (564301) 1140 (564401) => (two LNB powered/ CAM inserted)
Protection level IP 20
* Power consumption is measured with input signal.
The power consumption indicated for CAM and LNB are highest; in any case, depend on the type of CAM and LNB for each facility.
The technical specifications are defined for an ambient temperature of 45 ° C (113 ° F). For higher temperatures forced ventilation will be used.