Ashly Audio PE - Manual (Page 10)

. 10 -
PE-800 PE-1200 PE-1800 PE-2400 PE-3000 PE-3800
Power Output
Stereo Mode, both channels driven
8 ohms, 20 Hz - 20 kHz, 1% THD
200 W 300 W 500 W 700 W 900 W 1,100 W
4 ohms, 20 Hz - 20 kHz, 1% THD 400 W 600 W 900 W 1,200 W 1,500 W 1,900 W
Bridged Mono Mode
8 ohms, 20 Hz - 20 kHz, 1% THD
800 W 1,200 W 1,800 W 2,400 W 3,000 W 3,800 W
Parallel Mono Mode
2 ohms, 20 Hz - 20 kHz, 1% THD
800 W 1,300 W 1,800 W 2,400 W 3,000 W 3,800 W
Signal to Noise (20 Hz-20 kHz,
unweighted):
>98 dB >105 dB >108 dB >110 dB >111 dB >112 dB
Voltage Gain: 26 dB, 32 dB or 1.5 V sensitivity (selectable)
Output Circuitry: Bipolar, Class AB Bipolar, Class AB Bipolar, Class H Bipolar, Class H Bipolar, Class H Bipolar, Class H
Power Requirements (1/8 Power
Pink Noise @ 4 Ohm):
420W 640W 611W 790W 1010W 1220W
All Models
Distortion (SMPTE, typical) - 8 ohm
load, 10 dB below rated power
<.01%
Distortion (THD+N, typical) - 8 ohm
load, 10 dB below rated power, 20
Hz - 10 kHz
<.01%
Frequency Response 20 Hz - 20 kHz, +/- 0.15 dB
Damping Factor - 8 ohm load, < 1
kHz
> 400
Input Impedance 20 kOhm, balanced
Maximum Input Level: +21 dBu
Input Clipping
Cooling
temperature dependent speed-controlled axial fan
Control Network: onboard, compatible with standard 100 MB Ethernet hardware
Front Panel Indicators Per channel: Clip, -6 dB, -12 dB, -18 dB, Temp, Output current.
Overall: power, standby, protect, bridged mono, parallel mono, communications
Attenuators: Per channel: front panel, software, offset and remote
Input Connectors, each channel XLR female/TRS, Euroblock, XLR male (looping)
Output connectors, each channel Speakon, screw terminals (Model 800 and 1200 only)
Amplifier Protection inrush current limitation, temperature monitoring heat-sinks, output DC protection, power transistor
SOA protection, output over-current protection, mains fuses protection
Load Protection Adjustable clip limiter
Power Cable Connector 15A Edison 20Amp 30A Twistlock
Dimensions 19"W x 3.5"H x 15.5"D (483mmW x 88.9mmH x 394mmD)
Weight 22 lbs. (9.98kg) 23 lbs. (10.43kg) 24 lbs. (10.89kg)
Optional Protea NE /DSP Input Card
Latency Analog - 1.512 ms at 48KHz sampling.
Digital - 0.784 ms at 96KHz sampling.
A/D, D/A Converters: 24-bit
DSP 32-bit, floating-point
Digital Input Type AES3, 16-24 bit, 44.1 to 96 kHz.
Signal Flow Architecture "Click and hot plug" flexible architecture, non-compiling
Available Processing Blocks
Equalization Parametric, Notch, Graphic, Shelving, HPF/LPF, All pass
Signal Delay Up to 967msec any input/output
HPF/LPF Up to 8th order (48 dB/octave)
Compressor/Limiter, Gate, Meter
Signal Generator Pink noise, White Noise, Sine Wave
Level Control With or without VCA-type subgrouping