Peg-Perego John Deere Farm Tractor with Trailer - Manual (Page 5)

35), insert the axle prepared previously, and
hammer in fully.
15 • Separate the wheels and fit them by pressing
the wheel group down onto the base of the
trailer.
16 • Insert the red coupling into the hole on the
trailer (see figure).
17 • Couple the trailer onto the back of the tractor,
rotating the red lever. Figure 1: the trailer can
be uncoupled; figure 2: the trailer coupled.
WARNING: The trailer will hold a load weighing
up to 5 kg.
This product conforms to EN 71 the
safety standard for toys.
This vehicle is not intended for use
on streets, around traffic or parked
cars.
This product meets and/or exceeds
all ASTM TOY SAFETY STANDARDS,
including F 963, Consumer Toy
Safety Specifications.
MAINTENANCE AND CARE
• Regularly check the conditions of
the vehicle. In case of fault, do not
try to use the vehicle. For repair
use only original PEG PEREGO’s
spare parts.
• PEG PEREGO assumes no liability if
the product as been tampered
with.
• Do not leave vehicle near sources
of heat such as radiators, stoves,
fireplaces, etc.
• Protect vehicle from water, rain,
snow, etc.
• Periodically lubricate (with a light
weight oil) moving parts, such as
wheel bearings, steering linkages,
and chains at points of rotation or
where they come in contact.
• The vehicle’s surface can be
cleaned with a dampcloth. Do not
use abrasive cleaners. The cleaning
must be carried out by adults only.
• Never disassemble the vehicles
mechanisms unless authorized by
PEG PEREGO.
SAFETY
WARNING!
THE CAR MUST BE USED UNDER
ADULT SUPERVISION.
• Not suitable for children under the
age of 2 years. The small pieces
could be swallowed or inhaled.
• Never use the vehicle on steep
slopes, near steps or stairs, in the
middle of traffic or between
parked cars.
• Children should always wear shoes
when riding in or driving a ride-
in/ride-on vehicle.
• Do not allow children to place
their hands, feet or any part of
their body, clothing or other
articles near the moving parts
while vehicle is in operation.
• Never use gasoline or other
• PEG PEREGO® thanks you for choosing this
product. For over 50 years, PEG PEREGO has been
taking children for an outing: first with its famous
baby carriages and strollers, later with its pedal and
battery operated toy vehicles.
• Read this instruction manual carefully to learn the
use of the vehicle and to teach your child safe and
enjoyable driving. Please keep this manual for use
as a reference in the future.
• Our toys conform with the safety requirements
provided by the Council of the EEC, of the T.Ü.V.; of
the I.I.S.G. Istituto Italiano Sicurezza Giocattoli, and
the U.S. Consumer Toy Safety Specification F963.
Peg Perego S.p.A. is an ISO 9001
certified company.
The fact that we are certified provides
a guarantee of our honesty for our
customers, and fosters trust in the
company’s way of working.
• Peg Perego reserves the right to modify or change
its product. Price, literature, manufacturing
processes or locations or any combination of the
above mentioned entities may change at any time
for any reason without notice with impunity.
Years 2-4
Weight capacity
50 lbs
PEG PEREGO offers after-sales services, directly or
through a network of authorized service centers for
repairs or replacement parts. See the back cover of
this instruction manual for contact information.
CAUTION:
ADULT ASSEMBLY REQUIRED.
USE CARE WHEN UNPACKING AS
COMPONENTS TO BE ASSEMBLED
MAY POSE A SMALL PARTS/SHARP
EDGE HAZARD.
ASSEMBLY
1 • Unscrew the 2 knobs under the seat.
2 • Position the seat as shown in the figure.
3 • IMPORTANT: the seat can be adjusted to 2
positions depending on the height of the child
(see figure). Position 1: the seat is higher and
further back. Position 2: the seat is lower and
further forward.
4 • Turn the vehicle on its side, keeping the seat in
position. Unscrew the chain cover under the
vehicle.
5 • Open the cover to access the seat fixing screws.
6 • Screw on the two seat fixing knobs as shown in
the figure. Close and screw on the cover.
7 • Position the steering wheel. Fix the steering
wheel with the screw and washer provided.
8 • Push on the steering wheel cap as shown in the
figure.
TRAILER
9 • Position the trailer base on the bucket, oriented
as shown.
10 • Snap on the 5 pegs, ensuring they are fully
inserted.
11 • Insert a self-locking washer into the conical tool
provided. IMPORTANT: the washer flanges must
be orientated towards the inside of the tool
(see detail A).
12 • Remove the axle from the packaging and
remove the protective caps, if present. Insert
the axle, hitting it with a hammer until fully
inserted into the tool. When finished remove
the tool.
13 • Slide the 2 wheels onto the axle. IMPORTANT:
check that the wheels are correctly inserted,
with the hub caps facing out.
14 • Put a self-locking washer into the tool (figure
ENGLISH
CUSTOMER SERVICE
ASSEMBLY INSTRUCTIONS
VEHICLE MAINTENANCE
AND SAFETY
flammable substances near the
vehicle.
• The vehicle is constructed just for
one child.