Peg-Perego Case IH Magnum Tractor - Manual (Page 10)

CAUTION:
ADULT ASSEMBLY REQUIRED.
USE CARE WHEN UNPACKING AS COMPONENTS TO BE ASSEMBLED MAY POSE A SMALL PARTS/SHARP EDGE
HAZARD.
BATTERY ALREADY INSTALLED IN VEHICLE.
1-2 • Turn tractor upside down, remove the trailer chassis from underside of the tractor chassis by removing the screw.
3 • Insert washer shaped retainer into retainer installation tool with the finished side facing up. ATTENTION: the tabs on the self-locking washer must be turned
towards the interior of the tool (see detail A).
4 • Place one end of trailer axle into retainer installation tool and pound axle into tool (and retainer) until fully seated.
5 • Insert white bushing into the inside of each trailer wheel as shown.
6 • Install the following components onto axle; 1) washer 2) wheel (hubcap facing down) 3) 2nd wheel (hubcap facing up) 4) washer. ATTENTION: Check to
make sure that the wheels have been inserted correctly on the axle. The hubcaps must be facing away from the toy.
7 • Place retainer into installation tool, place tool onto upper end of axle and pound until seated. Remove tool.
8 • Place wheel & axle assembly onto trailer chassis with washers outside of posts and press down until axle is firmly seated into chassis.
9 • Insert red pin into trailer chassis tongue.
10 •Remove the 5 protective caps from the bottom of the trailer.
11 •Assemble gray trailer sides together with finished sides facing out.
12 •Place trailer sides firmly into stake pockets in trailer bed.
13 •Turn trailer bed upside down, place trailer chassis onto bed, align the 5 pegs in the red bed with the 5 holes in the black chassis and very firmly press or pound
pegs into the holes with hammer until firmly seated.
14 •Install hood by inserting lower black hinged tongue into slot on chassis. Rotate hood closed and turn black latch with coin to secure.
15 •Place the chrome decals into the headlight section of the front grill. Then attach the clear plastic cover; press the attachments into the 4 slots to form the front
headlight.
16 •Press the side inserts into place on the body.
17 •Unscrew the knobs on the bottom of the seat.
18 •Place seat bolts into red seat support holes.
19 •The seat can be adjusted to 2 positions to suit the height of the child (see figure).
20 •After adjusting the seat, tighten the 2 knobs that hold it in place.
21 •Insert front red seat support fingers into chassis.
22 •Rotate support (and seat) down onto chassis at the rear. Turn tractor chassis upside down and secure support to chassis with 2 screws.
23 •Apply the chrome decals to the taillight positions as shown in the figure.
24 •Attach the taillight lenses by pressing from the bottom upwards.
25 •Install left & right black plastic covers into “C” slots on each rear fender.
26 •Press the gas tank cap into place on the back of the tractor.
27 •Press the trim piece into place under the steering wheel.
28 •Install steering wheel; reach under tractor to find metal steering column tube. Push it upward as far as possible and hold it.
29 •Place steering wheel onto tube, align bolt holes.
30 •Install bolt and nut. Tighten.
31/2•Place exhaust stack firmly into bracket and secure with long screw.
33 •Attach the trailer to the tractor as follows: insert the trailer coupling into the opening on the back of the tractor, and rotate it (see fig. 34).
34 •Position 1: the trailer can be removed.
Position 2: the trailer is locked into place.
WARNING: The trailer will hold a load weighing up to 10 kg/22 lbs.
VEHICLE FEATURES AND INSTRUCTIONS FOR USE
35 •GEAR SHIFT LEVER. This vehicle has 2 speeds + reverse, with PARENTAL CONTROL: When produced, IT IS RESTRICTED TO SLOW SPEED and REVERSE
ONLY (For safety, shifter must be held in reverse to back up).
36 •TO ACCESS HIGH SPEED (see red bar beneath shift lever) remove screw, rotate red bar 90 degrees counterclockwise and replace screw.
37 •ELECTRIC ACCELERATOR with SmartPedal Technology™. When accelerator is pressed completely down, forward motion is activated. When pedal is
released halfway, neutral coasting action is engaged. Brake activates automatically when the child takes his foot off the accelerator. New SMARTPEDAL
TECHNOLOGY feature allows for longer runtime and more realistic driving. 3 position SmartPedal accelerator; 1) up = off/brake 2) ½ down = coast. 3) run
BATTERY RECHARGE
WARNING:
WARNING: BATTERY CHARGING AND ANY OTHER OPERATION ON THE ELECTRICAL SYSTEM MUST BE
CARRIED OUT BY ADULTS ONLY.
THE BATTERY CAN ALSO BE CHARGED WITHOUT REMOVING IT FROM THE VEHICLE.
38 •Install Battery: Open hood by turning black latch with 90 degrees with a coin. Rotate hood forward to open.
39 •Insert the battery charger plug into an electrical outlet. Connect point B to point C on the battery charger.
When the battery has been completely recharged, disconnect the battery charger from the electrical outlet, and disconnect point C from point B.
40 •Insert point B into point A, pressing until it clicks into place. Replace the battery brace. Always remember to close and fasten the hood on the battery
compartment when you have finished working on the battery.
REMOVING THE BATTERY
41 •Open the hood, as described above. Disconnect the battery from the electrical system by squeezing the sides of the plugs.
42 •Loosen the 2 screws on the battery brace, as shown in the figure.
43 •Remove the battery.
44 •Remove the battery clamp from the dead battery.
INSTALLING BATTERY
45 •If you have bought or own a Peg Perego 12V/12Ah battery, you will have to remove the plastic filler (A) by slipping it off the battery clamp.
46 •Reposition the new battery with the battery clamp in its housing. Fasten the clamp with the two screws.
47 •Connect the battery plug to the electrical system.
48 •Close again the cab by repositioning the hook, as done above.
ASSEMBLY INSTRUCTIONS
INITIAL BATTERY CHARGE
!• Remove battery and charger from packaging. Connect battery charger to a 120vac wall recepticle. Connect battery charger to battery.