Krix Seismix 3 - Manual (Page 7)

7
Due to continued development specifi cations may change without notice.
Seismix 1 V4.0: specifi cations
Drivers
Bass Driver
Electronics
Amplifi er Power
Amplifi er S/N
Distortion
- Input to Speaker
Line Level Inputs
General
Frequency Range
Output
Auto Power On / Off
Phase Select
Filters
Cabinet
Enclosure Type
Dimensions
Material
Finish
Weight
Nominal 200mm (8”) diameter paper cone driver, 38mm long throw
voice coil, developed for high level, low frequency reinforcement
200 watts RMS into the nominal 4 ohm driver
Maximum instantaneous power 400 watts
>85dB
<0.2% - @ 150 watts RMS
Left Input (mono)
200mV RMS for maximum output
Left + Right Input (stereo) 100mV RMS for maximum output
27Hz - 200Hz (-6dB) in room response
116dB maximum SPL in room response
10 minute delay before switching to standby after no input signal
0° to 180° continuously variable (relative to input signal)
Lowpass fi lter 50-200Hz 2nd Order
Highpass fi lter to limit driver excursion below 26Hz
Bass refl ex, down-fi ring vent
375mm high (inc. feet) x 295mm wide x 320mm deep
17mm MDF
Vinyl or lacquered timber veneer
11kg
specifi cation and features
additional features
Symetrix Vent
The Seismix subwoofer enclosure features
Symetrix bass refl ex venting, with the vent
exhibiting the same fl are radius internally and
externally. This lowers subwoofer distortion
and serves to reduce vent turbulence or
“chuffi ng” at high drive levels.
Clipping Protection
When faced with a signal peak which is in
excess of what the Seismix can accurately
reproduce, a limiter circuit activates to reduce
the level of the signal once it passes the preset
threshold. This permits the Seismix to perform
at high level with only a mild reduction in the
signal’s dynamic content.
Fault Protection
In the unlikely event that the amplifi er’s
temperature rises above 65 degrees celsius,
the amplfi er will shut-down until the
temperature drops below 65°C.
warranty
5 years warranty applies to the cabinet and
speaker.
1 year warranty applies to the amplifi er and
related internal electronics.
(Refer to the details on the warranty card
supplied)
queries
If you have any queries regarding the Seismix
Cube, the set up procedure or any other Krix
product, please contact your nearest Krix
retailer or Krix directly. Contact details are on
the back cover of this booklet.
Nominal 275mm (11”) diameter paper cone driver, 50mm long throw
voice coil, developed for high level, low frequency reinforcement
300 watts RMS into the nominal 4 ohm driver
Maximum instantaneous power 600 watts
>85dB
<0.2% - @ 200 watts RMS
Left Input (mono)
300mV RMS for maximum output
Left + Right Input (stereo) 150mV RMS for maximum output
22Hz - 200Hz (-6dB) in room response
122dB maximum SPL in room response
10 minute delay before switching to standby after no input signal
0° to 180° continuously variable (relative to input signal)
Lowpass fi lter 50-200Hz 2nd Order
Highpass fi lter to limit driver excursion below 26Hz
Bass refl ex, front vented
450mm high (inc. feet) x 360mm wide x 410mm deep (inc. grille)
17mm MDF
Vinyl or lacquered timber veneer
18kg
Seismix 3 V6.0: specifi cations
Drivers
Bass Driver
Electronics
Amplifi er Power
Amplifi er S/N
Distortion
- Input to Speaker
Line Level Inputs
General
Frequency Range
Output
Auto Power On / Off
Phase Select
Filters
Cabinet
Enclosure Type
Dimensions
Material
Finish
Weight