General specifications – E-Z-GO EXPRESS L6 User Manual
Page 27

2 - 7
GENERAL SPECIFICATIONS
Read all of this manual to become thoroughly familiar with this vehicle. Pay particular attention to all Notices, Cautions, Warnings, and Dangers.
2
MODEL: EXPRESS L6
TYPE: ELECTRIC POWERED PERSONNEL CARRIER
MODEL YEAR: 2012
Part No: 618867
Precision Drive System™ (PDS): Factory programmable to application
Solid State continuously variable seperately excited speed controller
Eight, 6 Volt Deep Cycle
Inductive throttle sensor
Diagnostic indicator
Dash mounted direction selector switch (Forward-Neutral-Reverse)
Anti-roll back, walkaway braking and alarm
Full torque, reduced speed reverse
Anti-stall motor protection
Regenerative ’Pedal Down’ and/or ‘Pedal Up’ braking
Factory selectable performance options
Drive Train:
Direct motor shaft connected to transaxle pinion shaft
Motor:
48 volt DC shunt wound, brazed armature, solid copper windings. Non-vented 15.2 hp (11.3 kW) at 1600 rpm (1hour)
Battery Charger: Delta Q, 48 VDC. H120/230 VAC 50/60 Hz. Underwriters Laboratories (U.L.) Listed, (C.S.A. Certified)
Transaxle:
Differential with helical gears
Brakes:
Dual rear wheel mechanical self-adjusting drum brakes. Automatic single point park brake release
with self-compensating system.
Capacity:
Choice of 6 seats (Std) or 4 seats and optional Wood Stake Sides or Roto-molded Cargo box.
Cargo Bed: Roto-molded cross-linked polyethelene. Removable hinged multi-position tailgate requires no latch mechanism.
Electrical System: 48 Volt DC, eight, 6 volt deep cycle storage batteries (107 minute, 225 amp-hour @ 20 hr. discharge rate)
PRODUCT SPECIFICATION
CONFIGURATION HIGHLIGHTS
PRODUCT OVERVIEW
Power Source
Drive Train
Motor Shaft Direct Drive
Differential with helical gears
Dash Mounted Forward-Neutral-Reverse
14.7:1
Some items shown may be optional equipment
Specifications are subject to change without notice
* Field installed accessories may require installation charges
48 Volts DC
Motor Type
Continuous Horsepower (kW)
Electrical System
Batteries (Qty, Type)
Key or Pedal Start
Speed Controller
Transaxle
Gear Selection
Shunt Wound
Rear Axle Ratio
2.5 hp (1.9 kW)
Intermittent Horsepower (kW) 18.1 hp (13.5 kW) @ 1900 rpm
48 Volt
Eight, 6 Volt Deep Cycle
Pedal Start
Battery Charger
48 VDC Delta Q, 120/230 VAC,
UL & CSA
400 Amp Precision Drive System (PDS)
Performance
Vehicle load capacity
6 Person
720.0 lb (325.0 kg) (Without Batteries)
Seating (Rear Facing Seat)
4 Person
Seating (Bed/Stake sides)
Dry Weight
1198.0 lb (540.0 kg)
Curb Weight
1210.0 lb (545.0 kg)
Towing Capacity
25.5 ft (7.8 m)
Outside Clearance Circle
6.5 ft (1.98 m)
Intersecting Aisle Clrnce
Speed (Level Ground)
16.0 mph ± 0.5 mph (26.0 kph ± 0.8 kph)
N/A
Steering & Suspension
Service Brake
Self-compensating rack and pinion
Leaf springs with hydraulic shock absorbers
Steering
Front Suspension
Rear wheel mechanical self-adjusting drum
Rear Suspension
Leaf springs with hydraulic shock absorbers
Self-compensating, single point engagement
Terra Trac 23 x 10.5 - 12 on Alloy Wheel
Parking Brake
Front Tires
Terra Trac 23 x 10.5 - 12 on Alloy Wheel
Rear Tires
Body & Chassis
Injection molded TPO
Welded steel with DuraShield™ powder coat
Frame
Front Body & Finish
Injection molded TPO
Rear Body & Finish
Fiberglass & Gelcoat
Seat Pod
Black
Standard Color
Dimensions
Overall Height (No Canopy)
Overall Height (With Canopy)
Wheel Base
Front Wheel Track
Rear Wheel Track
Gnd Clearance @ Differential
Vehicle Power
138.0 in (351.0 cm)
46.5 in (119.0 cm)
Overall Length
Overall Width
95.0 in (241.0 cm)
38.5 in (98.0 cm)
7.0 in (18.0 cm)
37.5 in (95.0 cm)
76.0 in (193.0 cm)
52.5 in (133.5 cm)
(Top of steering wheel)
Noise & Vibration
Sound pressure; continued A-weighted equal to or less
than 64 db(A)
Highest RMS value of weighted acceleration is less
than 2.5 m/s
2
Highest RMS value of weighted acceleration is less
than 2.5 m/s
2
The uncertainty of measurement is 0.46 m/s
2
Noise
Vibration, WBV
Vibration, HAV
Measurement methods were applied per the ISO 2631 and ISO 5349 standards
under conditions of typical vehicle surfaces.