beautypg.com

EZ-ACCESS TRANSITION MODULAR ENTRY MAT User Manual

Instructions transitions, Modular entry mat, Fig. 1

background image

Instructions

TRANSITIONS

®

Modular Entry Mat

Available in 2½” height (optional Risers also offered)

10270 REV 12-15-14

CE Technical Files kept at: Enable Access, Marshmoor Works Great North Road, North Mymms Hatfield, AL9 5SD, UK

© Homecare Products, Inc. All rights reserved.

All text and images contained in this document are proprietary and may not be shared, modified, distributed, reproduced, or reused

without the express written permission of EZ-ACCESS

®

.

MPORTANT INFORMATION

Rated load is 850 pounds. Never exceed rated load.
Read and follow all labels, instructions, safety and maintenance

information before use.

For additional care, use or safety information, or to obtain

replacement copies, please call 1-800-451-1903 or visit
www.ezaccess.com.

Do not use if ramp is damaged or unstable.
For wheelchairs and scooters only (not intended for commercial

use).

Ramp may be slippery when wet or icy.
Use only if sufficient maneuvering room is available at both ends of

the ramp to assure safe travel when entering and exiting the ramp.

Use ramp only with a qualified helper and always use your lap belt.
It is important that you refer to your equipment's (wheelchair or

scooter) User Guide for the proper degree of incline or decline and
chair direction before attempting ramp use. Never exceed its
recommendations
.

FITTING A MODULAR ENTRY MAT

The mat can be easily trimmed to accommodate lower heights and narrower
widths and, if necessary, notched to suit the doorjamb configuration.
Alternately, mat can be combined with an additional Modular Entry Mat and
one set of

Risers to create a maximum height of 4¾”.

1.

If door threshold is equal to the height of the Modular Entry Mat

(2½”

high), use mat as is (FIG. 2, section A).

2.

If door threshold is less than the height of the Modular Entry Mat

(2½”

high), trim mat to the desired height, depth and/or width using a
reciprocating saw, razor knife, or hand saw (FIG. 1).

Use caution when operating any non-manual saw as serious

injury may result due to unexpected binding or pinching of
rubber mat

material. Always follow tool manufacturer’s safety

guidelines.

3.

If door threshold is greater than the height of the Modular Entry Mat

(2½”

high), two Modular Entry Mats (shown in FIG. 2, sections A & B) along
with one pair of Risers (FIG. 2, section C) can be combined to
accommodate a rise up to 4¾” high.

With this configuration, section A must remain at its original
height (ok to trim width only).

a. FIG. 2, section B, can be trimmed to the desired height, depth

and/or width. If section B is trimmed, section C, which is used to
increase overall height, needs to be trimmed to match the depth
and/or width of section B.

b. Secure section B to section C using supplied Phillips Head

Screws.

FASTENING THE MAT

It is recommended that the mat be securely fastened.

1.

ATTACHING TO WOOD

a.

Place mat in desired location and ensure that
surface is free of dirt and debris.

b.

Secure mat using supplied Phillips head screws
(2 each). Space screws evenly (see FIG. 2 for
placement) and drive until head is ¼” below the
mat surface.

2.

ATTACHING TO CONCRETE

a.

Place mat in desired location and ensure that
surface is free of dirt and debris.

b.

Using a ¼” diameter masonry bit, drill a hole 2”
deep 1” from the corner edges at the taper
(FIG. 2).

Ensure the holes are free of any
residue.

c.

Drive the supplied ¼” diameter mushroom
head pin anchors (two each) into the holes
with a hammer until the head is seated.

SAFETY AND MAINTENANCE

1.

At all times, keep mat clear of snow, ice, dirt,
leaves, and other debris that may accumulate on
the surface.

2.

Clean mat with mild soap and warm water. Rinse
well and use extra caution when mat surface is wet.

WARRANTY

Three-year limited warranty. See reverse side of
document for details.

















FIG. 1









FIG. 2