Ds p, S p 1, Lp n – Clay Paky POINT MH User Manual
Page 3: P a n, L r h, U c f, E n a, S l a, O n d, C c s
S
E
ENTER
SELECT
L
I
Press UP/DOWN to
select tIL function.
Press ENTER to access
the function.
S
E
ENTER
SELECT
L 0
The display shows the
minimum position (LO)
for Tilt movement.
Press ENTER to confirm.
S
E
ENTER
SELECT
H I
Press UP-DOWN to
select the maximum
position (HI) for Tilt
movement.
Press ENTER to confirm.
S
E
ENTER
SELECT
5
5
Press UP-DOWN to
select a value between 0
(corresponding to 0°)
and 255 (corresponding
to 208°).
Press ENTER to confirm.
The display shows: LO.
S
E
ENTER
SELECT
5
5
2
Press UP-DOWN to
select a value between 0
(corresponding to 0°)
and 255 (corresponding
to 208°).
Press ENTER to confirm.
The display shows: Hl.
Nota: To select value 0 quickly, press the UP button while
pressing DOWN. Vice versa, to select value 255 quickly,
press the DOWN button while pressing UP.
S
E
ENTER
SELECT
L
I
Press SELECT to return
to tlL.
S
E
ENTER
SELECT
d
S P
Press UP/DOWN to
select SPd function.
Press ENTER to access
the function.
The display shows the
set speed.
S
E
ENTER
SELECT
S P 1
Press UP/DOWN to
select the desired speed
from the settings:
SP1 (lowest speed)
SETTING DMX ADDRESS
1
S
E
ENTER
SELECT
Press SELECT.
The red led lights up.
5
S
E
ENTER
SELECT
Press UP/DOWN to
select the address.
Press ENTER to confirm.
Example: If the projectors use 4 channels, the first one
should have address 1; the second one address 5; the
third one address 9 and so on.
If the projectors use 6 channels, the first one should have
address 1; the second one address 7; the third one
address 13 and so on.
N.B.: For the last address, you have to consider the
channels used by the last projector so as not to exceed
the maximum value of valid addresses (507).
N.B.: In the setting phase, if you press DOWN while
pressing UP the address decreases to the minimum
value (1). Vice versa, if you press UP while pressing
DOWN the address increases to the maximum value
(507).
Opt
OPTION MENU
(the options must be set on each individual projector)
S
E
ENTER
SELECT
O P
Press SELECT twice.
The red led lights up and
the display shows: OPt.
Press ENTER to confirm.
The display shows: Pln.
S
E
ENTER
SELECT
l
P
n
Press ENTER to access
Pln function.
S
E
ENTER
SELECT
n
O
With the UP/DOWN
button, select On to
activate, Off to disconnect.
Press ENTER to confirm.
The display shows: Pln.
S
E
ENTER
SELECT
l n
Press UP-DOWN to
select tln function.
Press ENTER to access
the function.
S
E
ENTER
SELECT
n
O
Using the UP/DOWN but-
ton, select On to activate,
Off to disconnect.
Press ENTER to confirm.
The display shows: tln.
P
ROGRAMMING OPERATION WITH
CONTROL UNIT
tlL
FUNCTION
: vertical movement angle
SPd
FUNCTION
: Pan and Tilt movement speed
S
E
ENTER
SELECT
5
5
2
Press UP-DOWN to
select a value between 0
(corresponding to 0°)
and 255 (corresponding
to 360°).
Press ENTER to confirm.
The display shows: Hl.
Nota: To select value 0 quickly, press the UP button while
pressing DOWN. Vice versa, to select value 255 quickly,
press the DOWN button while pressing UP.
S
E
ENTER
SELECT
P A n
Press SELECT to return
to PAn.
Pln
FUNCTION
: Pan horizontal movement inversion
tln
FUNCTION
: Tilt vertical movement inversion
Hlr
FUNCTION
: Pan/Tilt high resolution
FuC
FUNCTION
: colour disc positioning only
on full colours
S
E
ENTER
SELECT
l r
H
Press UP-DOWN to
select Hlr function.
Press ENTER to access
the function.
With this function, the projector uses 6 control channels
and gives greater resolution to Pan/Tilt movements.
S
E
ENTER
SELECT
n
O
Using the UP/DOWN but-
ton, select On to activate,
Off to disconnect.
Press ENTER to confirm.
The display shows: Hlr.
S
E
ENTER
SELECT
u C
F
Press UP-DOWN to
select FuC function.
Press ENTER to access
the function.
S
E
ENTER
SELECT
n
O
Using the UP/DOWN but-
ton, select On to activate,
Off to disconnect.
Press ENTER to confirm.
The display shows: FuC.
Press SELECT twice to return to rest mode.
SELECTING SLAVE MODE (SLA)
S
E
ENTER
SELECT
O P
Press SELECT twice.
The red led lights up and
the display shows: OPt.
S
E
ENTER
SELECT
A u
Press UP/DOWN to
select the automatic Aut
menu.
Press ENTER to confirm.
The display shows: EnA.
S
E
ENTER
SELECT
E n A
S
E
ENTER
SELECT
S L A
Press ENTER to access
EnA operating mode.
The display shows one
of the three following
modes: SLA - SA - SAt.
Press UP-DOWN to
select SLAVE (SLA)
mode.
Press ENTER to confirm.
The display shows: EnA.
Press SELECT twice to return to rest mode and to
eventually program the functions in the Opt options menu.
Press SELECT twice to return to rest mode.
DISPLAY AT MAXIMUM LUMINOSITY /
DISPLAY OFF
S
E
ENTER
SELECT
O P
Press SELECT twice.
The red led lights up and
the display shows: OPt.
Press ENTER to confirm.
The display shows: Pln.
S
E
ENTER
SELECT
O n
d
Press UP-DOWN to
select dOn function.
Press ENTER to access
the function.
S
E
ENTER
SELECT
n
O
Using the UP/DOWN but-
ton, select On to activate,
Off to disconnect.
Press ENTER to confirm.
The display shows: dOn.
dOn
FUNCTION
: display at maximum luminosity
S
E
ENTER
SELECT
C C
S
Press UP-DOWN to
select SCC function.
Press ENTER to access
the function.
S
E
ENTER
SELECT
n
O
Using the UP/DOWN but-
ton, select On to activate,
Off to disconnect.
Press ENTER to confirm.
The display shows: SCC.
SCC
FUNCTION
: turns off the lamp during colour
change
SP2 - SP3 - SP4 - SP5 (highest speed).
Press ENTER to confirm. The display shows: SPd.