Acoustic Image Series III - Manual (Page 7)

System
Power Amp (all models)
Included Accessories
Frequency Response 20 Hz - 20 kHz, ±0.5 dB
Distortion <0.5%, full output, <0.1%, typical
Hum and Noise -85 dB or better
AC Power 115V/60 Hz or 230V/50 Hz, switchable
Size 10x8x3.5 inches (Clarus/Focus)
10x6.5x3.1 (Focus SA)
Weight Less than 5 lbs for all models
3.5 lbs (Focus SA)
Topology Class D (PWM)
Switching Frequency 230 kHz
Output Power-Clarus >250W (8 >400 W (4 ), >500W (2 )
Output Power-Focus 450 8 1000
Minimum Load 2
Output Connectors Neutrik Speakon type (pole 1)
Input (Focus SA only) XLR-1/4 in combo jack, 5k
Sensitivity (SA only) 250 mVrms for full output (”instrument level”)
Gig bag with shoulder strap, 6 foot
Speakon to 1/4 inch cable
Japan version is 100V, 50/60 Hz only
Mic Input 600 ohm balanced, XLR connector
Phantom Power 38 volts, on/off switch w/LED indicator
Instrument Input 1 M impedance, 1/4 inch jack
Direct Out +4 dB, balanced, XLR connector, ground lift,
pre/post EQ selector
Effects Loop Parallel type with return level control
Bass Control Shelving type, ±15 dB at 60 Hz
Mid Control ±15 dB at 650 Hz
Treble Control Shelving type, ±25 dB at 10 kHz
Notch Filter >-18 dB sweepable from 30 to 800 Hz
Low Cut Filter -12 dB/octave sweepable from 30 to 800 Hz
Type Digital with 6 presets and level control
Program Presets 3 reverb (hall, room, plate), delay, ambient
chorus, flange
> W (8 > 00 W (4 ), > W (2 )
Preamp (Mic and Instrument Inputs through combo jack)
Effects (Clarus 2R and Focus 2R))
W
W), W W
W), W W
W
W
Warranty Information
Serial Number _______________
Acoustic Image Phone: 919-785-1280
5820 Triangle Drive Fax: 919-785-1281
Raleigh, NC 27617 www.acousticimg.com
9
Specifications
FCC Compliance Notice
This device complies with part 15 of the FCC rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesired operation.
CAUTION: Changes or modifications not expressly approved
by the party responsible for compliance could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of
the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiated
radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and
receiver.
--Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician
for help.