MTD 110-500 - Manual (Page 3)

PARTS LIST FOR MODEL NO. 110-500
Raf.
No.
Port
No.
DESCRIPTION
Ref.
No.
Port
No. DESCRIPTION
1 305-7072 Grips — White 36 710-191 Hex Hd. Cap Sew. 3/8-24 x 1-1/4 Ig.
2 310-8846 Throttle Control - Complete (Heat Treated)
3 305-7470 Knob + 37 310-8835 Sluing Lever Assembly
4 310-8841 Throttle Control Bracket + 38 305-7520 Knob - Red
5 901-7627 Ferrule Assembly + 39 347 -8809 Blade Reinforcement Plate
6 732-139 Conduit and Wire + 40 310-7492 Wheel Pivot Bai
7 710-606 HexHd. Cap Sew. 1/4-20 x 1-1/2 Ig. * 41 736-133 Flat Washer 3/8 ID *
8 712-107 Hex Centerlock Nut 1/4—20 thread * 42 712-116 Elastic Stop Nut 3/8—24 thread *
9 310-9364 Handle — Upper (2 Req’d) 43 901-7805 Blade Spindle Ass’y — Complete
10 710-106 HexHd. Cap Sew. 1/4—20 x 1-1/4 Ig. * 44 712-526 Speed Nut
11 310-8334 Handle - Lower 45 710-116 HexHd. Cap Sew. 5/16-18 x 2 Ig. *
12 310-9060 Handle Bracket 46 710-473 Truss Hd. Mach. Sew. #10-24 x 1/2 Ig. *
13 710-209 Sems HexHd. Cap Sew. 3/8—16x5/8 Ig. * 47 736-147 External Lockwasher #10 Screw ♦
14 501-9184 Wheel Assembly — Rear 48 310-9925 Pulley — 4” dia. — 1/2” bore
15 734-237 Tire-Rib Tread 14” dia. x 1-3/4” 49 736-921 Spring Lockwasher — 1/2” screw *
16 734-238 Wheel Assembly — Rear . Tire 50 712-922 Hex Jam Nut 1/2 — 20 thread ♦
17 748-147 Flange Bearing (2 Req’d Per Wheel) 51 754-116 V-Belt42” X 1/2” ♦
18 738-114 Axle Bolt — Rear 52 347 -8295 Blade Soindle Cover
19 712-123 Hex Nut 5/16 — 24 thread * 53 710-158 HexHd. Cap Sew. 5/16-24 x 1-1/4 Ig.
20 736-119 Spring Lockwasher 5/16 Screw * 54 736-170 Lockwasher — Special
21 312-8125 Blade - 21” 55 711-250 Spacer
56 756-121 Pulley — Engine — 4” dia.
23 710-117 HexHd. Cap Sew. 5/16—24 x 1 Ig. 57 710-938 Allen Set Sew. Cup Pt. 1/4—28 x 1/4 Ig.*
(Heat Treated) 58 746-145 Cable Clip
24 736-169 Spring Lockwasher — 3/8” Screw * 59 714-365 Key-Hi Pro # HP 505 * A
25 710-113 HexHd. Cap Sew. 3/8—24 x 1-5/8 Ig. 60 712-267 Hex Nut 5/16-18 thread *
(Heat Treated) 61 711-240 Spindle A
26 748-100 Blade Adapter 62 721-105 Seal A
27 736-105 Belleville Washer 63 741-107 Timken Bearing —3/4 Bore — lower A
28 736-112 Belleville Washer 64 719-120 Spindle Housing A
79 347-9169 Frame Assembly 65 741-120 Timken Bearing — 11/16 Bore —upper A
30 347-9069 Deck Assembly 66 736-154 Flat Washer A
31 310-7386 Washer 67 711-212 Sleeve A
32 710-152 HexHd. Cap Sew. 3/8—24 x 1 Ig.
33 SlO-9392 Wheel Assembly — Front
34 305-7006 Fortiflex Bearing
35 738-213 Axle Bolt
* For faster service obtain standard nuts, bolts and washers locally. If these items cannot be obtained locally, order by
part number and size as shown on parts list.
+ Included in Part No. 310-8846 Control-Throttle (complete).
A Included in Part No. 901-7805 Blade Spindle Ass’y (complete).
ASSEMBLY
Your new mower is shipped completely assembled with the
exception of the handle.
1. Remove lawn mower and all parts from carton. Make
certain that all loose parts and literature are removed
from carton before carton is discarded.
2. Extend throttle control assembly, which is attached to
rear of mower and place on floor. CAUTION: Do not bend
or kink control wire.
3. (a) Snap lower handle into position on two lugs which
extend from the handle brackets mounted on the rear
of the frame assembly®
(b) Assemble the two upper handle parts with cap screws
and locknuts provided in parts bag. The yellow cap
screw should be used to attach throttle control assem­
bly to upper handle as shown in diagram. Do not
tighten nuts.
(c) Attach upper handle assembly to lower handle with
cap screws and locknuts. Tighten all nuts.
(d) Secure control wire to lower handle with cable clips.
4. Check blade bolts for proper tightness.
5. See initial belt adjustment under Adjustment Section on
page U .
OPERATION
NOTE: For shipping purposes your mower is set with the
v/heels in a low cutting height position. For best results
raise the cutting position until it is determined which
height is best for your lawn. See adjustments.
1. Service engine with gas and oil. See Engine Manual pack­
ed with lawn mower for complete instructions for the care
and maintenance of engine.
Read Directions Carefully.
2. When ready to start engine, place throttle control lever,
on handle, in “Choke” position and start engine in
accordance with instructions in Engine Manual. After
engine starts, move throttle control lever, on handle, to
desired engine speed. The engine is stopped by placing
control lever on handle in the “Stop” position.
3. Be sure that lawn is clear of stones, sticks, wire or other
objects which could damage lawn mower or engine. For
best results and to insure more even grass distribution,
do not mow when lawn is excessively wet.
FORM NO. 770-2799C