AT&T 9111 - Manual (Page 5)

TEIEPHONE OPERATION
continued
Handset Receiver Volume Control
(located on the left side of the
handset)
1 To increase the sound level, press
the ( a ) key.
2 To decrease the sound level, press
the ® key.
Special lUephone Senices
If you subscribe to special local
telephone company services like
Call Waiting or Call Forwarding,
you can access them by pressing
I
FLASH I whenever you would press
the switchhook on a regular phone.
To redial the last number dialed from
the handset;
1 Press ШШ\.
2 Wait for the PHONE indicator to
go on and for a dial tone.
3 Press IflEDMtl.
The last number you called is stored
in the redial memory until you dial
another number.
№ie
Mute allows you to Ьещ" your caller
but prevents the caller from hearing
you.
1 Press ШШ.
2 The MUTE/LOW ВАТТ indicator
will light to indicate the Mute
feature is activated.
3 To continue your conversation.
press
\MUTE\
again.
Rngernte
Press
\MUT£\
on the handset during
incoming ringing to disable the
ringer for the duration of the call.
Hold
The Hold feature allows you to keep
a call on the line while you step
away from the phone or while you or
someone else takes the call on an
extension phone.
1 Press I
HOLD
I.
2 The PHONE indicator will blink
slowly to indicate the call is on
hold.
3 To release Hold, press I
HOLD \
again.
IMPORTANT: If you are using the
Hold feature to switch to another
extension, you must first place the
call on Hold. After the extension
phone has been picked up, release
the Hold feature and press \QFF\ on
the 9111 to resume your conversation
on the extension phone.
Advanced AiioSetect leaiire
The Cordless Telephone 9111’s
advanced AutoSelect feature will
automatically select the clearest
channel, even during a conversation.
During automatic channel change
your conversation may be interrupted
for about 1 second while the unit
scans and selects a new channel.
ICmporaiy Tone
If you have dial pulse (rotary)
service, this feature allows you
to enter codes or tones needed to
operate answering machines, or use
electronic banking services, calling
cards, and other special services.
This feature will operate most special
services; however, some services
may actually require a touch tone
line. To be sure, ask the company
that provides the special service.
NOTE: If you have touch tone
service, you do not need to use the
Temporary Tone feature.
To use temporary tone dialing:
1 Dial the call normally.
2 Press SM.
3 Enter numbers or symbols
required.
4 End the call normally (Temporary
Tone is automatically shut off).
nognMiniig Hie Hnger ivpe
The handset ringer is capable of four
different types of ringing tones. The
following sections detail how to
change the different tones and to
turn off the ringer on the handset.
To program, the handset must be
C^.
To select a different ringer type do
the following:
1 Press IPROGI.
2 Press [#).
3 Press a key (|Т)-Щ) to select a
ringer type.
4 Press \0FF\,
Hiring on the Hnger
To turn off the ringer on the handset,
do the following;
1 Press \PR0G\.
2 Press И.
3 Press [o] to turn off the ringer.
4 Press I Off I.
To turn ringer on again, see
“Programming the Ringer Type.”
Checking the ringer
To check the ringer which is currently
programmed, do the following:
1 Press I PROP I
2 Press И.
3 Press (Z) again to check the ringer.
4 Press
\0FF\.
PageAfcndset locator
This feature is useful if you misplace
the handset.
To locate the handset using the
Handset Locator feature:
1 Press I PAGE/HANDSET LOCA TOR I.
2 A repeating paging tone is
sounded at the handset for
approximately 30 seconds.
To cancel the Handset Locator
feature:
Press I Off I on the handset or press
\ PAGE/HANDSET LOCATOR \ on the base.